Installation Instructions

ManualsBrandsMagick Woods ManualsBath26"W x 17-1/8"D Concord Collection Vanity and White Vanity Top with Integrated Sink

PRODUCT: 26 in. CONCORD ENSEMBLE

DIMENSIONS: 26 in. W x 17-1/8 in. D* x 34-1/16 in. H (*depth with vanity top)

(Depth without vanity top: 12-15/16 in.)

MATTE WHITE MODEL: 39458

DARK CHOCOLATE MODEL: 816

CONCORD VANITY ENSEMBLES

Thank you for selecting our product. To ensure that your installation goes smoothly, please read

these instructions carefully before you begin. Also review the recommended materials and tools for a

smooth installation. Before you start, verify that you have all the mentioned components for your

vanity base model shown below and ensure that all are free from defects. If any part is missing or

damaged, contact Customer Service for replacement parts.

• Faucets not included

Knob (2x)

INSTALLATION INSTRUCTIONS FOR:

Base (1x)

Foot (4x)

1 in. screw (8x) 1 in. screw (2x)

PRODUCT: 34 in. CONCORD ENSEMBLE

DIMENSIONS: 33-11/16 in. W x 18-7/8 in. D* x 34-1/16 in. H (*depth with vanity top)

(Depth without vanity top: 13-1/8 in.)

MATTE WHITE MODEL: 42415

DARK CHOCOLATE MODEL: 42416

PRODUCT: 41 in. CONCORD ENSEMBLE

DIMENSIONS: 41-9/16 in. W x 19-7/8 in. D* x 34-1/16 in. H (*depth with vanity top)

(Depth without vanity top: 14 in.)

MATTE WHITE MODEL: 39460

DARK CHOCOLATE MODEL: 39456

Porcelain top (1x)

Questions, problems, missing parts? Before returning to your retailer, call our Customer Service

department at 1-855-995-5578, 8:30 a.m. - 5 p.m., CST, Monday - Friday. contactus@magickwoods.com

Knob (4x)

Base (1x)

Foot (4x)

1 in. screw (8x) 1 in. screw (2x)

Porcelain top (1x)

1-1/2 in. screw (2x)

Knob (8x)

Base (1x)

Foot (4x)

1 in. screw (8x) 1 in. screw (2x)

Porcelain top (1x)

1/2 in. screw (6x)

Summary of content (4 pages)

PAGE 1
CONCORD VANITY ENSEMBLES Thank you for selecting our product. To ensure that your installation goes smoothly, please read these instructions carefully before you begin. Also review the recommended materials and tools for a smooth installation. Before you start, verify that you have all the mentioned components for your vanity base model shown below and ensure that all are free from defects. If any part is missing or damaged, contact Customer Service for replacement parts.
PAGE 2
PREPARATION Tools Required for Assembly (not included): • Tape Measure • Electric Drill with #2 Drill Bit (A) • Straight Edge or Leveling Meter • (2) #8 x 2 in. Screws (B) • (2) Wall Anchors - if the vanity will not be screwed to wall studs (C) Estimated Installation Time: 2 hours (including removal of old vanity if applicable) WARNINGS & CAUTIONS WARNING: Two people are required for safe installation. Take extra precautionary measures to ensure a secure grip on the vanity base and top when lifting.
PAGE 3
Step 3: Using your level, locate any uneven floor and/or wall areas where your vanity will be installed. Unevenness can cause your vanity to become misaligned resulting in twisting of the cabinet. Repair any uneven areas by reducing high spots or shimming low spots. Step 4: 1) Place the vanity in the desired position taking into account the location of your plumbing. 2) Ensure the vanity is level front to back and confirm at both sides.
PAGE 4
Step 6: Place the porcelain top centered on the vanity base. Connect the pipes/faucets correctly and ensure that there is no leakage. Figure 4a: 26 in. base. Figure 4b: 34 in. base. Figure 4c: 41 in. base. Figure 4a: 26 in. base Figure 4b: 34 in. base Figure 4c: 41 in. base TROUBLESHOOTING Problem : Vanity doors/drawers rub against another surface. There is a large uneven gap between the vanity doors/drawers. Possible Cause : Floor is not level.