Model #: ___________________________ Serial #: ___________________________ Date Purchased: ___________________ Installation & Operation Manual MKG24, MKG36, MKG48, MKG60 & MKG72 All Options Built After August 1, 2005 C E E S I G N D D E R T I F I CERT I F I ED L25-052 Rev.
TO THE PURCHASER, OWNER AND STORE MANAGER Please review these warnings prior to posting them in a prominent location for reference. TO THE PURCHASER WARNING Post in a prominent location the instructions to be followed in the event that an operator smells gas. Obtain this information from your local gas supplier. WARNING DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Table of Contents MKG Series Gas Griddle 1. INSTALLATION SECTION ...................................................................................... 4 1.1. 1.2. 1.3. CHECKING YOUR NEW GRIDDLE .................................................................................................... 4 INSTALLATION CLEARANCES.......................................................................................................... 4 GAS CONNECTION(S) .............................................................
Installation MKG Series Gas Griddle 1. Installation Section 1.1. Checking Your New Griddle Your new griddle has been carefully packed into one crate. Every effort has been made to ensure that your new griddle is delivered to you in perfect condition. As you unpack your new appliance, inspect each of the pieces for damage. If something is damaged, Contact the shipper immediately; the shipper is only responsible for 15 days after delivery.
Installation MKG Series Gas Griddle WARNING NEVER supply the appliance with a gas that is not indicated on the data plate. Using the incorrect gas type will cause improper operation. If you need to convert the appliance to another type of fuel, contact your dealer. 1.3.1. Fuel Type(s) Each appliance is equipped to work with one type of fuel. The type of fuel with which the appliance is intended to operate is stamped on the data plate, see Figure 1.
Installation MKG Series Gas Griddle 1.5.1. Counter Use With Legs CAUTION To prevent equipment damage, DO NOT tilt your MagiKitch'n griddle on only two legs, or on its sides. (See Figure 2) A set of 4” legs is shipped with the appliance (unless appliance was specifically ordered without legs). A threaded receptacle is located near each corner of the underside of the base of the appliance, on appliances 48" and wider there are threaded receptacles in the front and rear center of the base.
Installation MKG Series Gas Griddle NOTICE The larger units have 6 threaded receiving holes, but require only the four 1/2" bolts on each corner to mount the griddle. 1. Remove (4) existing 1/4-20 nuts and bolts from the rear corners of the equipment stand. 2. Align the 2 bolt holes on the rear corners of the stand with the 2 bolt holes on the rear mounting brackets. Orient the brackets as shown in Figure #4 on this page. 3.
Installation MKG Series Gas Griddle 1.6. Final Gas Connection A properly installed gas supply system will deliver adequate pressure (7 to 8 inches w.c. for natural gas, 11 to 12 inches w.c. for propane) to all appliances connected to the line, operating at full demand. 1.6.1. Regulator Assembly An adequate gas supply is important for the appliance to operate properly. Undersized lines or lowpressures will restrict the volume of gas required for satisfactory performance.
Operations MKG Series Gas Griddle 2. Operation Section Ensure that a proper installation has been performed on the appliance and that all warnings, cautions, and notices contained in this manual have been read, understood and adhered to before proceeding. 2.1. 2.1.1. Lighting Instructions Snap-Action Thermostat Appliances LEFT PIEZO IGNITOR RIGHT PIEZO IGNITOR PILOT HOLES 1. Turn all thermostat knobs to the “OFF” position. METHOD 2.
Operations MKG Series Gas Griddle 2.2. Initial Startup NOTICE New griddles should be carefully tempered and cared for in order to avoid possible damage. To break in a new griddle, do the following: Wipe the griddle surface clean. A mild soapy water solution may be used to clean the surface, if this solution is used be sure to rinse thoroughly with fresh water to eliminate any soap residue. Also it is important to wipe the griddle surface and surrounding areas to dry up any standing water.
Calibration MKG Series Gas Griddle 3. Thermostat Calibration Section Each control typically operates a pair of burners with a Snap action, Electric or Solid State. The controls were set at the factory. However, if the griddle’s surface temperature varies greatly from the setting on the thermostat knob, adjust the thermostat using the following procedure: 3.1. Calibration Procedures 3.1.1. 1. 2. 3. 4. 5. 6. Snap Action And Electric Thermostat Light pilots as described in section(s) 2.1.1 and 2.1.2.
Basic Operation MKG Series Gas Griddle 4. Basic Operation 4.1. Operational Helpful Hints 1. Each thermostat controls 12" of griddle surface, whenever possible, use the leftmost or rightmost thermostats for the lowest cooking temperatures. The adjacent thermostats set at higher temperatures will effect centrally located thermostats. 2. For quicker thermostat response during heavy loading of the griddle, load product directly over the thermostat sensing probe.
Cleaning & Maintenance MKG Series Gas Griddle 5. Cleaning & Maintenance Section 5.1. Daily Cleaning 1. Clean the griddle surface often to prevent sticking and poor food product quality. Scrape the griddle plate regularly with a scraper intended for your type of griddle surfaces to remove all surface grease and food debris. NOTICE Do not use Grill Bricks, Grill Screens, or any other type of abrasive material on your MagiKitch'n Chrome Griddle Surface. USING ABRASIVE MATERIALS WILL VOID YOUR WARRANTY. 2.
Cleaning & Maintenance MKG Series Gas Griddle 9 9 Check to see that the ventilation hood and make up air systems are working properly. Any make up air system should not be directed as to impede the flow of combustion air to the griddle, or flue exhaust from the griddle. Inspect griddle surface for any visible damage. 5.4. Annual/Periodic Preventative Maintenance and Inspection This section should ONLY be performed by a qualified service technician as part of a regular kitchen maintenance program.
Trouble Shooting MKG Series Gas Griddle 5.6. Trouble Shooting Charts The following charts may help to eliminate any basic operational problems that you may be experiencing with your appliance. Locate the problem on the left side of the chart, and cross-reference with the possible cause. Once the problem has been identified take the appropriate action to rectify the problem. 5.6.1.
Accessories MKG Series Gas Griddle 6. Accessories 6.1. Standard All plain steel and chrome plated griddles are shipped with a set of 4” adjustable legs. The appliance also comes equipped from the factory with a manual gas shutoff valve, and the specified gas regulator for the model and gas type purchased. Each MKG Chrome surfaced griddle is equipped with a Chrome Kit which includes a cleaning brush, cleaning powder, spatula, scraper, and scraper blade replacements.
Accessories MKG Series Gas Griddle WORKSHELVES WITH AND WITHOUT TOWEL BARS TOWEL BAR ONLY PAN CUTOUTS AND CUTTING BOARDS ARE AVAILABLE ON LARGER WORKSHELVES 6.2.2. Cutting Boards Size 8" X 12" Cutting Board 8" X 24" Cutting Board 8" X 48" Cutting Board 8" X 72" Cutting Board Part No. 1604-0643600-C 1604-0643700-C 1604-0643800-C 1604-0643900-C Other sizes are available, consult factory for size, price, and availability. L25-052 Rev.
Accessories MKG Series Gas Griddle 6.2.3. Warming Shelves, Rear Shelf Model C/A, Shelf Rear MKG24 C/A, Shelf Rear MKG36 C/A, Shelf Rear MKG48 C/A, Shelf Rear MKG60 C/A, Shelf Rear MKG72 Part No. 5225-1535701-C 5225-1535702-C 5225-1535703-C 5225-1535704-C 5225-1535705-C Shelf Kits can be attached to existing models. The Stainless Steel shelf is removable from the shelf framework for easier cleaning if necessary. REMOVABLE SHELF EXISTING BOLTS ON APPLIANCE 18 L25-052 Rev.
Accessories MKG Series Gas Griddle 6.2.4. Equipment Stands Equipment stands can be ordered with legs or casters (stands with casters shipped after May 2006 are equipped with adjustable casters). NOTE: It should also be noted that when ordering an equipment stand for your MKG appliance, you will also need to order and MKG Joining Kit, Part No. 7225-1512101.
Accessories MKG Series Gas Griddle 6.2.5. Miscellaneous Your appliance can also be used with the following miscellaneous accessories so you can customize your operation to your specific demands.. The wall spacers listed below insure that you cannot push the appliance too close to the rear wall. The Utensil box gives you a handy location to store your cooking tools. The Utensil box does not interfere with any controls, and can be moved from one end of the griddle to the other without the use of tools.
Notes MKG Series Gas Griddle 7. Notes Page L25-052 Rev.
Notes MKG Series Gas Griddle This Page Intentionally Left Blank 22 L25-052 Rev.
Notes MKG Series Gas Griddle This Page Intentionally Left Blank L25-052 Rev.
In the event of problems with or questions about your order, please contact the MagiKitch’n factory at (800) 258-3708 US and Canada only (603) 225-6684 World Wide www.magikitchn.com In the event of problems with or questions about your equipment, please contact the MagiKitch’n Authorized Service and Parts representative (ASAP) covering your area, or contact Pitco at the numbers listed to the left. MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501 SHIPPING ADDRESS – 10 FERRY ST.
