Owner’s/Installation Manual 7" Color LCD Monitor Model: M125C For Technical Assistance, please call (800) 638-3600, or visit www.magnadyne.
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning / Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Monitor Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor Features and Controls 1 2 3 4 5 6 1. LCD Screen 2. IR Sensor: Receives signal from the remote control. 3. LED Power Indicator: A red LED indicates the vehicle’s ignition is “On” and the monitor is in the “standby” mode. When the vehicle is put into reverse or the turn signals are used the camera’s image will automatically appear on the display. Note: The cameras can not be manually selected in this mode.
Remote Control Functions 1 MUTE POWER 7 8 2 CH 3 MENU CH 4 9 5 MODE CALL TIMER 6 LANG SYS SEL 10 11 12 1. Mute: Push to "Mute" the volume. 2. : Press this button to select between a Mirror or Normal screen image. : Press this button to flip the screen image vertically. 3. POWER: Press this button to turn the unit "On" or "Off". 4. MENU: Press this button to select a desired menu. 5. MODE (Picture Mode): Press to select between Personal, Standard, Soft, Vivid and Light picture settings. 6.
General Operation Camera View Selection and A/V Input: Left Side Camera: The left side view camera (CAM1) is designed to automatically turn on whenever the vehicle’s left turn signal is activated. Right Side Camera: The right side view camera (CAM2) is designed to automatically turn on whenever the vehicle’s right turn signal is activated. Rearview Camera: The rearview camera (CAM3) is designed to automatically turn on whenever the vehicle is placed into reverse gear.
General Operation (continued) Monitor Adjustment The monitor has three basic menus: Picture, Option and System. To scroll through the three basic menus continuously press the MENU button. Picture Menu Press the Menu button on either the monitor front panel or remote control until the PICTURE menu screen is displayed. Use the buttons on the remote to scroll through the menu items and select from the menu items: VOLUME, BRIGHT, CONTRAST, COLOR, SHARP and HUE.
Front Panel Video Input Yellow RCA: Video (Cable Not Supplied) Auxiliary Video Input You can connect the video output signal of a digital camera, camcorder or video device. Select the auxiliary video input mode by pressing the SEL button on the monitor until DVD appears in the display. Cable Suggestions: Radio Shack #42-2551 or #42-2483.
Wiring Diagram Red Wire: 12 Volt Switched (DC 12~32V) Black Wire: Ground (GND) 2 Amp White Wire: Left Trigger (LEFT TRIG) Gray Wire: Right Trigger (RIGHT TRIG) Green Wire: Rear Trigger (REAR TRIG) 5. Ground REAR TRIG 1. +12 Volts 2. N/A 4. Video 3. Audio C125 (Rearview) 3. N/A 1. +12 Volts 2. N/A C-SDR (Right Side) 5. Ground CAM1 (White Connector) 4. Video 3. N/A 8 CAM2 (Gray Connector) 4. Video LEFT TRIG 2. N/A 5. Ground RIGHT TRIG 1.
Installation Instructions The monitor can be mounted via a pedestal-mount, U-support bracket or a flush-mount. Pedestal Mounting the Monitor 1. Loosen the thumb wheel on the base support so the nut attached to the thumb wheel can slide into the monitor’s mounting channel. 2. Slide the thumb wheel nut into the channel on the back of the monitor. 3. Position the monitor to the desired height and tighten the base support thumb wheel. 4. Adjust the tilt lever. 5.
Installation Instructions Flush Mounting the Monitor 1. Locate a suitable location for mounting the monitor (In-Dash, In-Wall, Headrest, etc.). Then cut a 7-1/8" (W) x 4-7/8" (H) opening and insert and secure the flush-mount housing. 2. After securing the housing, insert the monitor into the housing. Do Not Apply Pressure Directly to the LCD Monitor’s Screen. Utilize the outer edges to gently push the monitor into the housing until it snaps into place.
Maintenance Although this monitor requires little care, you can still maintain its condition and performance by following these steps: • Keep the system away from excessive moisture, extreme heat or cold, and magnetic fields. • Occasionally clean the monitor screen with damp soft cloth. Should you experience any problem with the system please refer to the troubleshooting guide prior to returning your system for repair.
Warranty ONE (1) YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agents will within one year from the date of sale to you, repair, replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective in materials or workmanship, when properly connected and operating on the correct power requirements designated for the specific product.
