Owner`s manual

Power is ON but no screen • Check whether the connection of the antenna,cable receiver or satellite box is connected correcLJ)_
image. • Check whether ail the cablesto the unit are connected to the correct Output jack of your device like BJuray disc/DVD recorder:
• Hake sure that the selected input mode isconnected to the working input jack.
• Check if your computer" is NOT in sleep mode when the input mode of this unit is in PC mode.]ap any key on the keyboard to
wake up your"computer:
No picture or"sound Check if the Power is on.
Check whether all the cablesto the unit are connected to the correct Output jack of your"device like Biu ray/DVD recorder:
View other]V channels.Theproblem might be limited to the broadcasting station or"weak signalstrength.
Unplug the AC power cord and wait for"about I minute,then plug the AC power cord and]brn On the unit again.
Check whether the connection of the antenna,cable receiver"or"satellite box is connected correctly.
Hake sure that the selected input mode is connected to the working input jack.
Check if your computer" is NOT in sleep mode when the input mode of this unit is in PC mode.]ap any key on the keyboard to
wake up your"computer:
• Hake sure that the sound isnot muted. Pressn_( so that the volume bar"and current volume levelwill appear"on the]V screen.
• Hake sure that the volume isNOT set to 0 or"l_X. if so,use VOL +/- to adjust to the desired volume.
No color • View other]V channeB.The problem might be limited to the broadcasting station or"weak signalstrength.
. Adjust Color in Picture settings.,,J p.18
No sound,distorted sound or" • Nake sure that the Analog Audio signalsfrom the HDNI DVI device are connected to the Analog Audio (UP,)input jacks.
incorrect Audio Sound isheard • When using Component AnalogVideo, Composite AnaiogVideo or"PCVGAVideo make sure that the Analog Audio (L/R)
when usingthe HDNI DVI connectors are mounted into the Audio (UP,)input jacks.
connections.
Adjusted Picture or Sound • You must set Home in Location. ,,,_p.26
settings are not effective every Othervdse,the settings you adjusted wJJ] not be memorized after the unit goes into Standby mode.
time the unit isTbrned On.
Sound OK, picture poor"
Picture OK, sound poor
You see a distorted picture or"
hear" an unusual sound.
Ghosts, lines or'streaks in picture •
You see noise or'trash on the
screen.
Different color marks on the]V •
screen
Electrical interference from nearby appliances may affect picture quality.
Adjust Contrast and Brightness in Picture settings, u,_ p.18
View other]_! channels.The problem might be limited to the broadcasting sta±Jon or weak signal strength.
For the best picture qualit}4 watch High Definition wide screen programs.
If the HD content is not available, watch Standard Definition programs instead.
View other]_! channels.The problem might be limited to the broadcasting sta±Jon or weak signal strength.
Check if the audio cable is connected into the unit correctl}4
You may be getting interference from electrical appliances, automobiles, motorcycles or fluorescent lights.
]}'y moving the unit to another" location to see if this is the cause of the problem.
Electrical interference from nearby appliances may affect picture quaJit}4
View other]h! channeB.The problem might be limited to the broadcasting station or" weak signal strength.
When the capabilities of the unit exceed the capabilities of the Digital broadcasting, the signal vviJJbe increased to match the
capabilities of the display of the unit.This may cause noise or" trash.
View other]h! channels.The problem might be limited to the broadcasting sta±ion, missing da±a or" pixela±ion.
Captions are displayed as a white
box. No caption is dispbyed in
the Closed Caption supported
program.
Black box is displayed on the]V
screen.
You svdtch to a difierent input • This unit vdll memorize the volume level from the last time you adjusted it.
and the volume changes. • If the volume of the sound from another" device is higher" or" bwer, then the loudness vviJJchange.
• Make sure Auto volume leveling is setto On. u,j p.19
You svdtch to a different input • This unit wiJJ memorize the viewing mode from the last time you used the particular input modes.
and the screen size changes.
The display image does not • If you are using the unit as a PC monitor, make sure that Horizontal position and Vertical position in PC settings are set correctly.
cover the entire screen. • If you are watchingTV or" using the CompositeVideo, ComponentVideo or" HDNI vdth 480i input, press FORMAT repeatedly to
svdtch various screen modes.
• Interference from buildings or" weather conditions may cause captioning to be incomplete if watchingAnalogTV signals.
• Broadcasting station may shorten the program to insert advertisements.
• The Closed Caption decoder" cannot read the information of the shortened program.
• The text mode is Selected. For" caption, select CC-1, CC-2, CC-3, CC-4 or" Off.
The LCD screen is manufactured to provide many years of useful life, Occasionally a few non active pixds may appear as a fixed point of blue, green or red.
This is not to be considered a defect in the LCD screen.
Some functions are not available in specific modes, but this is not a malfunction, Read the description in this Owner's Manual for more details on correct operations,