Owner’s Manual Manual del Propietario Manuel du Propriétaire 32MV402X 26MV402X 22MV402X Necesita ayuda inmediata? www.magnavox.com/support 1 866 341 3738 www.magnavox.com/support www.magnavox.
Contents 1 Notice 5 2 Important 7 7 7 7 Positioning the TV Regulatory notices Environmental care 3 Get started Features Supplied accessories Symbols used in this Owner’s Manual Attaching the base Mounting the unit on your furniture Managing cables Installing the remote control batteries Remote control function Control panel Terminals Connecting the antenna or the cable Plugging in the AC power cord Initial setup 4 Use your TV Switching on your TV and putting it in Standby mode Adjusting volum
Return your Product Registration Card or visit at www.magnavox.com/support today to get the very most from your purchase. Registering your model with MAGNAVOX makes you eligible for all of the valuable benefits listed below, so don't miss out. Complete and return your Product Registration Card at once or visit at www.magnavox.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
1 Notice MAGNAVOX is a registered trademark of Philips Electronics North America Corporation and is used by Funai Electric Co., Ltd. and Funai Corporation, Inc. under license from Philips Electronics North America. Funai reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this Owner’s Manual is believed adequate for the intended use of the system.
Copyright All other registered and unregistered trademarks are the property of their respective owners. The terms HDMI and HDMI HighDefinition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. is a trademark of SRS Labs, Inc.
2 Important Environmental care Positioning the TV • • • • • • • • • • • • Large screen TVs are heavy. 2 people are required to carry and handle a large screen TV. Make sure to hold the upper and bottom frames of the unit firmly as illustrated. Install the unit in a horizontal and stable position. Do not install the unit in direct sunlight or in a place subject to dust or strong vibration. Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.
3 Get started Features • Supplied accessories Owner’s Manual Quick Start guide Quick DTV /TV / CATV Information display • AutoProgram • Smart TV IMPORTANT Start You can use your remote control to select channels which are broadcast in Digital format and conventional Analog format. Also, cable subscribers can access their cable TV channels. • Registration card Box-inserts You can display the title, contents and other information of the current program on the TV screen.
Attaching the base Managing cables You must attach the base to the unit to have it as a table top unit. Be sure the front and rear of the base match the proper direction. For large screen TVs, at least 2 people are required for these steps. Route your antenna cable and all other cables through the cable management tie at the back of the TV. The holder helps keep your cables tidy and easily manageable. 1 1 1 Attach the cable management tie as illustrated below.
a b c j k l m d e f g (POWER-ON / STANDBY-ON) Press to Turn the unit On and go into Standby mode. To completely Turn Off the unit, you must unplug the AC power cord. b AUTO MODE Cycles through preset picture and sound settings. c FAV Displays a list of all channels marked as favorite. (Includes subchannels) d 0 − 9 (NUMBER buttons) Press to select channels. • (DOT) Press to shift the subchannel from the main channel. PREV.CH Press to return to the previously viewed channel.
a VOL ◄/► Touch to adjust volume down (◄) / up (►) or to move left (◄) / right (►) when selecting menu items. b CH ▲/▼ Touch to select channels or to move up (▲) / down(▼) when selecting menu items. c MENU Touch to display the Home menu. d SOURCE Touch to select the connected devices or to determine the setting when selecting menu items. Control panel f a b e (POWER-ON / STANDBY-ON) Touch to Turn the unit On and go into Standby mode.
Connecting the antenna or the cable Be sure your antenna or other device is connected properly before plugging in the AC power cord. If you connect to an antenna through RF cable Connecting a set-top box, Blu-ray / DVD recorder via composite connectors and Analog Audio Do not place your recorder too close to the screen because some recorders can be susceptible to signals. Any DTV programs that are broadcasted in your area can be received for free through an antenna connection.
System searching. Please wait... These operations are accessible by remote control. Some may also be accessible by control panel on the main unit. Digital channels found: Analog channels found: Initial setup Auto programming may take more than 20 minutes to complete. Digital channels will take longer than Analog to find and program. Please wait until you see the Auto Programming complete message.
4 Use your TV Switching channels Switching on your TV and putting it in Standby mode To Turn Power On or to Turn Standby On • Touch or press . on the front panel or the remote control. Note •• Energy consumption contributes to air and water pollution. When the AC power cord is plugged in, your TV consumes energy. Your TV has very low Standby power consumption.
Watching channels from an external device Smart TV Switching Each Input Mode can easily switch with the remote control between TV (DTV or Analog TV) and external devices when they are connected to the unit. Smart TV offers Internet services for your TV. Use the remote control to browse the Smart TV pages. You can play movies and much more, all from your TV screen. –– Because Smart TV is an online system, it can be modified over time to better serve its purpose.
Create and use lists of favorite channels You can create lists of your preferred TV channels so that you can find those channels easily. Select a list of favorite channels 1 Press FAV. fun-Link options If you have our brand products such as Blu-ray disc player or DVD recorder that are compatible with fun-Link functions, connect them to this unit via an HDMI cable so you can simply operate various items from this unit’s remote control.
For PC Input signal Changing picture format Display modes can be selected when your TV receives a 16:9 or 4:3 video signal. Three types of display modes can be selected for a PC Input signal. Press FORMAT repeatedly to switch the TV aspect ratio. Wide screen 4:3 Unscaled •• This unit can also be connected to your PC that has a DVI terminal. Use an HDMI-DVI conversion cable for this Video connection and it requires Stereo mini 3.5mm plug Audio cable for Analog Audio signal as well.
Picture (JPEG) USB Your TV is fitted with a USB connection that enables you to view photos, listen to music or watch video files stored on a USB Memory Stick. 1 2 onnect the USB Memory Stick to the USB terminal on the side of C your TV. Press and use ▲▼◄► to select USB, then press OK. Picture Music Video Use ▲▼ to select a file or a folder. avi Image4.jpg jpg Image5.jpg mp3 Image6.jpg Image1.jpg Image7.jpg Image2.jpg Image8.jpg Image3.jpg avi mp3 Image1.jpg Image2.jpg 2 Image3.
Music (MP3) 1 Video Use ▲▼ to select a file or a folder. avi Track4.mp3 avi Movie4.avi jpg Track5.mp3 jpg Movie5.avi mp3 Track6.mp3 mp3 Movie6.avi Track1.mp3 Track7.mp3 Movie1.avi Movie7.avi Track2.mp3 Track8.mp3 Movie2.avi Movie8.avi Track3.mp3 2 1 Use ▲▼ to select a file or a folder. Title: Artist: Album: Duration: 00:05:28 Year: Press OK or B to play the selected files. • Press OK, B or F to pause, then press OK, B or F again to resume. • Press D to skip to the next file.
5 Use more of your TV 3 This section describes the overview of the Setup menu displayed when you press and use ▲▼◄► to select Setup. The Setup menu consists of the function setting items below. 1 Press to display Home menu. Use ▲▼ to select the desired menu and an item, then press OK or use ▲▼◄► to determine the setting.
to select the desired setting, then press OK (Color alignment, Noise reduction, Black stretch, * Advanced picture Dynamic contrast, Gamma, MPEG artifact reduction, Color enhancement, Custom color management and Film mode) Picture Before you begin: You must set Home in Location. ➠ p.29 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into Standby mode. 1 2 Press Automatic Super zoom 4:3 and use ▲▼◄► to select Setup, then press OK.
*You can set a particular about picture quality in Advanced picture.
Digital TV operation Sound You can select the Audio language while your TV is receiving the Digital broadcasting. Before you begin: You must set Home in Location. ➠ p.29 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into Standby mode. 1 2 Press and use ▲▼◄► to select Setup, then press OK. Use ▲▼ to select Sound, then press OK.
Digital TV operation Features 1 2 Press and use ▲▼◄► to select Setup, then press OK. In addition to the basic Closed Caption, DTV has its own Closed Caption called Digital caption service. Use this menu to change the settings for Digital caption service. Use ▲▼ to select Features, then press OK.
Note •• Digital caption service that you can switch differs depending on the broadcast description. •• Closed Captioning service may not be controlled by this unit’s menu options if you are watching television through an external cable or satellite set-top box. In which case you will need to use the menu options on the external set-top box to control Closed Captioning. •• The captions do not always use correct spelling and grammar.
US movie ratings Channel lock Particular channels or external Input modes can be invisible in this function. 3 4 All Use ▲▼ to select the particular channels or external Input, then press OK repeatedly to switch between view and block. • indicates that the channel or Input Source is locked. • indicates that the channel or Input Source is not locked. Channel lock 40.1 DTV Sleeptimer TV ratings lock 40.2 DTV Child lock Movie ratings lock 40.3 DTV Canada English ratings lo 40.
Canada English or Canada French ratings You can select the rating for Canada English or Canada French broadcasting. 3 4 Use ▲▼ to select Canada English ratings lock or Canada French ratings lock, then press OK. Use ▲▼ to select the desired rating, then press OK repeatedly to switch between view and block. • indicates that the rating is locked. • indicates that the rating is not locked.
Channel installation Weak channel installation Be sure the RF cable is correctly connected to this unit and you are registered with your cable TV provider when you install cable channels. This function lets you add the channels that were not added by the AutoProgram due to the reception conditions during the initial setup. It is available only when you select Antenna in Installation mode. Autoprogram 1 2 If you switch wires (e.g.
Preferences Use Magnavox fun-Link You can set the unit to reduce the power consumption or adjust the backlight brightness in Location setting. fun-Link allows you to operate your connected fun-Link device. Your TV supports Magnavox fun-Link, which enables one-touch play and one-touch Standby between fun-Link-compliant devices. Compliant devices must be connected via an HDMI connector.
fun-Link (HDMI CEC) Device list This function allows you to operate the linked functions between our brand devices with a fun-Link feature and this unit connecting through an HDMI cable. You must connect this unit to our brand fun-Link devices and be sure its fun-Link (HDMI CEC) setting is also set to On. This function lets you see the product model number or name of connected devices. Use ▲▼ to select the desired fun-Link device listed on the TV screen, then press OK.
Wireless setting Network Set up network connection settings in order to use Smart TV or network upgrade function. • • Select to use a wireless LAN to connect to the Internet by wireless connection. 4 The meanings of abbreviations are defined as below. AP : Wireless LAN Access Point WPS : Wi-Fi protected Setup SSID : Wireless network name The key entry screen will appear when you select SSID, WEP /WPA /WPA2 or Proxy address. Use ▲▼ to select Wireless, then press OK.
Wireless network setting This menu is displayed only when you set Wireless in Network selection. In order to use a wireless network, you must set up a connection to the AP (e.g. wireless router). 3 Use ▲▼ to select Wireless network setting, then press OK. Auto Search for wireless networks automatically and select the SSID from the list. 4 5 Use ▲▼ to select Auto, then press OK. The list of wireless networks will be displayed. Use ▲▼ to select the appropriate the SSID, then press OK.
IP configuration In following cases, select IP configuration to set each setting as necessary. –– When connection test failed with the setting of Connection test. –– When instructed by your Internet service provider to make specific settings in accordance with your network environment. 3 4 Proxy configuration 3 4 Use ▲▼ to select a setting, then press OK. Network selection Proxy setting Use ▲▼ to select IP configuration, then press OK.
Setting status You can check the status of network settings. 2 Use ▲▼ to select Setting status, then press OK. • Network setting list will be displayed. • MAC address of this unit will be displayed in the list. Reset network settings You can reset the status of network settings. 2 3 Checking your current software version 1 Use ▲▼ to select Software information, then press OK. • The version and a description of the current software is displayed.
Upgrading the software USB upgrade You can upgrade the software by using USB Memory Stick. 1 Connect your USB Memory Stick with the upgrade file to the USB terminal on the side of your TV. 7 Press again to Turn the unit On. • The TV starts up with the new software. For further assistance, please contact Call Center. Note •• In order to update software via the Internet, you must connect the unit to the Internet and set up necessary settings. Network settings assistant ➠ p.31 Network ➠ p.
6 Connecting devices No supplied cables are used with these connections: •• Please purchase the necessary cables at your local store. Before you connect AC power cord: Be sure other devices are connected properly before plugging in the AC power cord. Connecting your devices HDMI Digital connection HDMI connection offers the highest picture quality. HDMI (High-Definition Multimedia Interface) transports high definition Digital video and multi-channel Digital Audio through a single cable.
HDMI-ARC connection Composite Analog Video Connection HDMI-ARC allows you to use fun-Link to output TV Audio directly to a connected Audio device, without the need for an additional Digital Audio cable. Composite Analog Video connection offers standard picture quality for video devices connected to the unit. If you connect to the unit’s Composite Video (Y/VIDEO) Input jack, connect Audio cables to the Audio (L/R) Input jacks. When the Audio is monaural, then only connect to the Audio L Input jack.
Connecting the TV to the Internet using a wireless LAN PC connection HDMI connection Broadband router This unit can be connected to your PC that has a HDMI terminal. Use an HDMI cable for this Digital connection. WLAN USB wireless LAN adapter Ethernet cable Internet IN OUT LAN HDMI cable Network provisioning equipment PC Note •• After you made the wireless connection, set up necessary network settings. Network ➠ p.31 •• Use a Wireless LAN Access Point (AP) (e.g.
The following video signals can be displayed: Format Resolution VGA 640 x 480 SVGA 800 x 600 XGA 1,024 x 768 1,280 x 768 1,360 x 768 WXGA Refresh rate 60Hz Other formats or non-standard signals will not be displayed correctly. Note •• Please purchase the VGA cable or HDMI-DVI conversion cable that has a ferrite core. •• The following operations may reduce noise. –– Attach a ferrite core to the AC power cord of your PC.
7 Useful tips FAQ Question Answer My remote control does not work. What should I do? •• Check the antenna or cable connection to the main unit. •• Check the batteries of the remote control. •• Check if there is an obstacle between the infrared sensor window and the remote control. •• Test the signal Output use IR Signal Check. ➠ p.43 If okay, then possible infrared sensor trouble. •• Aim the remote control directly at the infrared sensor window on the front of the unit.
Symptom Remedy No picture or sound •• Check if the Power is On. •• Check whether all the cables to the unit are connected to the correct Output jack of your device like Blu-ray / DVD recorder. •• View other TV channels. The problem might be limited to the broadcasting station or weak signal strength. •• Unplug the AC power cord and wait for about 1 minute, then plug the AC power cord and Turn On the unit again.
Symptom Remedy Cannot use the wireless connection. •• Check if the Wireless LAN Access Point (AP) (e.g. wireless router) is oriented properly or not placed too close between them. •• Once you have activated the wireless connection please wait 30 seconds for the connection to be established after Turning On the unit, before trying to access network features such as Smart TV. Cannot use Netflix feature. •• Netflix is available only in the United States and Canada.
8 Information Glossary Maintenance Cabinet Cleaning Analog TV (NTSC) Acronym that stands for National Television Systems Committee and the name of Analog broadcasting standards. Off-the-air NTSC signals are no longer being sent by major broadcasting stations in the USA. ARC (Audio Return Channel) HDMI-ARC allows you to use Magnavox fun-Link to output TV audio directly to a connected Audio device, without the need for an additional Digital Audio cable.
9 Specifications Model # 32MV402X 26MV402X 22MV402X Picture enhancement Type WXGA (1366 x 768 pixels 60Hz) Aspect ratio 16:9 Viewing angles 178° (V) by 178° (H) 150° (V) by 160° (H) Built-in Digital tuner 160° (V) by 170° (H) ATSC / NTSC Sound enhancement Mono / Stereo Mono, Stereo, SRS TruSurround XT® Power output (RMS watts) 8W x 2 2W x 2 Equalizer 5 band Ease of use SD (4:3 Source) Picture format : Automatic / Super zoom / 4:3 / Movie expand 14:9 / Movie expand 16:9 / Wide scr
10 Warranty LIMITED WARRANTY NINETY (90) DAY LABOR / ONE (1) YEAR PARTS WARRANTY COVERAGE: This warranty obligation is limited to the terms as set forth below. WHO IS COVERED: This product warranty is issued to the original purchaser or the person receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer.
License 1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6.
definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it).
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 9.
-------------------------------------------------------------------------------------------------lua-slncrypto 16.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
MINIX 3 DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE DATA FILES OR SOFTWARE. Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in these Data Files or Software without prior written authorization of the copyright holder.
1.9. 1.10. 1.11. 1.12. 1.13. 1.14. 2. 2.1 2.2. 2.3. 3. 3.1. 3.2. A. Any addition to the contents of a file containing Original Code and/or addition to or deletion from the contents of a file containing previous Modifications. B. Any new file that contains any part of the Original Code or previous Modifications. “Notice” means any notice in Original Code or Covered Code, as required by and in compliance with this License.
13. Miscellaneous. This License represents the complete agreement concerning the its subject matter. If any provision of this License is held to be unenforceable, such provision shall be reformed so as to achieve as nearly as possible the same legal and economic effect as the original provision and the remainder of this License will remain in effect.
FUNAI CORPORATION, Inc.