TVCR CC13C1MG CC19C1MG Color TV with built-in VCR Owner’s Manual
Return your Warranty Registration Card today to ensure you receive all the benefits you’re entitled to. Once your purchase is registered, you’re eligible to receive all the privileges of owning this product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 Welcome to your TV/VCR owner’s manual. This manual describes two models: CC13C1MG and CC19C1MG. The models may look different, but they operate exactly the same. The CC13C1MG is illustrated in this manual. The features described in this manual apply to all models unless otherwise specified.
Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hooking Up the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 2 3 Remove the battery compartment lid on the bottom of the remote control by pressing the tab, then lifting the lid. 1 2 3 Place two AA batteries inside the battery compartment with their + and – ends aligned as indicated. Replace the battery compartment lid.
Hooking Up the TV/VCR 1 Hook up your TV/VCR using one of the connections shown. A. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna Connect a Cable signal or an antenna to the ANT(enna) Jack. CC13C1MG ANT. ANT. B. Hooking Up Your TV/VCR With a Cable Box To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box. Connect the Cable signal to the IN Jack on the Cable Box.
Hooking Up the TV/VCR (cont’d) 7 D. Hooking Up Your TV/VCR to Another Video Source (VCR or Camcorder) You may need this connection if you want to copy tapes or view tapes that you are playing on the VCR or camcorder. Select channel 00 (A/V IN) at the TV/VCR when viewing tapes that are playing on the VCR or camcorder. Details are on page 31. AUDIO/VIDEO OUT Jacks on VCR 3CH 4CH AUDIO VIDEO OUT IN Connect an Audio cable to the AUDIO OUT Jack on the VCR and to the AUDIO In Jack on the front of the TV/VCR.
Turning On the TV/VCR Before you turn on the TV/VCR, make sure batteries are in the remote control and you have connected the TV/VCR correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 2 EJECT Press the POWER button. The TV/VCR will come on and the screen shown below will appear.
Language Selection 9 Follow the steps below to change the language of the on-screen displays and menus. 5 2-4 1 Press the MENU button. EJECT POWER PRESS B > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 2 1 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button. REC /OTR PAUSE /STILL PLAY REW PRIMARY SETUP F.
Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. 2-3 1 Press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS EJECT POWER 1 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 2 REC /OTR PAUSE /STILL PLAY Press the PLAY/▲ button or the STOP/▼ button to select PRIM.
Automatic Channel Setup (cont’d) 11 Adding/Deleting Channels 5 2,4 If your channel lineup changes, you may want to add newly available channels or remove channels that are no longer available in your area. You can use the CH(annel) o/p buttons to scroll through only the available channels. To add or delete channels from the TV/VCR’s memory, follow these steps. EJECT POWER 1 1 Press the MENU button. MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP > PRIM.
Setting the Clock There are three ways to set the clock: Manually, with Automatic PBS Channel Selection, or with Manual PBS Channel Selection. With manual clock setting, you tell the TV/VCR the current time. With Automatic or Manual PBS Channel Selection, the TV/VCR gets the time from your local PBS station. If you use either Manual PBS Channel Selection or Automatic PBS Channel Selection, follow the steps on page 19 to have the TV/VCR maintain the clock according to your Time Zone.
Setting the Clock (cont’d) 13 4 7 5-6 Press the PLAY/o button or the STOP/p button to select SET MANUAL CLOCK, then press the F.FWD/B button. SET MANUAL CLOCK TIME – – : – – DATE – – / – – / – – – – TO END PRESS EXIT 5 EJECT POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 0 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
Setting the Clock (cont’d) Automatic PBS Channel Selection 1 2-4 1 Press the MENU button. EJECT > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 2 4 POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button. 9 ALT.CH 0 REC /OTR PAUSE /STILL PLAY PRIMARY SETUP REW > SELECT LANGUAGE AUTO PROGRAMMING CH MEMORY REVIEW VOLUME BAR [ON] SET CLOCK F.
Setting the Clock (cont’d) 15 5 Press the PLAY/▲ button or the STOP/▼ button to select SET PBS CH. AUTO. Then, press the F.FWD/B button. 6 Wait for the TV/VCR to find the time. SET AUTO CLOCK TIME ––:–– EJECT DATE ––/––/–––– MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 NOW SEARCHING TO END PRESS EXIT 6 7 POWER 7 SLEEP/ WAKE UP 9 ALT.CH 0 NOW SEARCHING flashes on the TV/VCR screen.
Setting the Clock (cont’d) Manual PBS Channel Selection 1 2-4 1 Press the MENU button. EJECT > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 4 2 POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button. REC /OTR PAUSE /STILL PLAY PRIMARY SETUP REW F.
Setting the Clock (cont’d) 17 5 Press the PLAY/▲ button or the STOP/▼ button to select SET PBS CH. MANUAL. Then, press the F.FWD/B button. 7 AUTO CLOCK (PBS) CH 02 Wait for the TV/VCR to find the time. EJECT POWER TIME ––:–– DATE ––/––/–––– SELECT CHANNEL NUMBER TO END PRESS EXIT 6 6 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 8 9 ALT.CH 0 Use the Number buttons to select your PBS station.
Daylight-Savings Time When the Daylight-Savings Time feature is ON, the TV/VCR clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October. To turn Daylight-Savings Time ON or OFF, follow the steps below. 1 5 2-4 EJECT POWER Press the MENU button. > PRIM.
Time Zone 19 When you set the clock using AUTO CLOCK, specify your time zone. The TV/VCR will maintain the clock according to your time zone. 1 1 2-5 Press the MENU button. EJECT POWER > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 6 2 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button.
Front Panel CC13C1MG Cassette Compartment Insert a video cassette tape here. Wireless Remote Sensor Receives a signal from your remote control so you can operate the TV/VCR from a distance. STOP/EJECT Button Press once to stop the tape. When playback is stopped, press to eject the tape. Press to select an item in the menu. VIDEO In Jack Connect this jack to the video out jack of a camcorder or a VCR. Details are on page 31. AUDIO In Jack Connect this jack to the audio out jack of a camcorder or a VCR.
Rear Panel 21 CC13C1MG ANT. AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR. ANT(enna) Jack Connect your antenna or cable here. Details are on page six. Antenna Hole Connect the stem of an indoor antenna here. Details are on page six.
Remote Control Buttons CLEAR Button Press to erase incorrect data when programming TV/VCR functions. Also, press to reset the real-time counter to 0:00:00. Details are on page 40. POWER Button Press to turn on or off the TV/VCR. EJECT Button Press to eject the tape. Number Buttons Use to select channels and to program TV/VCR functions (such as setting the clock). ● Cable Users Enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0,6.
Remote Control Buttons (cont’d) 23 MENU Button Press to display the main menu. You also may use the buttons on the front of the TV/VCR to access the main menu. Details are on page 20. STATUS/EXIT Button Press to access or remove the status display. Details are on page 26. Press to remove the menu. REC(ord)/OTR Button Press once to start a recording. Details are on page 29.
Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 4 2-3 1 Press the MENU button. EJECT POWER K > BRIGHTNESS PICTURE COLOR TINT SHARPNESS TV RESET K TO ADJUST PRESS { / B 2 3 Press the PLAY/▲ button or the STOP/▼ button to select the desired control (BRIGHTNESS, for example). Press the REW(ind)/{ button or the F.FWD/B button to adjust the picture control. (Refer to the chart on page 25.
Adjusting the Picture Controls (cont’d) 25 Decrease decreased brightness decreased contrast paler more purple softer BRIGHTNESS PICTURE COLOR TINT SHARPNESS Increase increased brightness increased contrast more brilliant more green clearer CC13C1MG Press the REW(ind)/{ button to decrease a picture control. Press the F.FWD/B button to increase a picture control. PLAY F.
On-Screen Status Displays A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below. If you select STATUS ON, then select COUNTER ONLY OFF: ● Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the status display also may appear when you press other function buttons.
Reminder 27 The channel number will remain on the screen at all times when you set REMINDER to ON. The exception is when closed captioning is selected. Set REMINDER to ON or OFF by following the steps below. 4 2-3 EJECT POWER 1 Press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 1 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 0 REC /OTR PAUSE /STILL PLAY 2 REW F.
Playing Follow the steps below to play a tape. 1 Insert a tape in the TV/VCR. The power will come on. If the tape’s record tab is missing, playback should start automatically. 2 1 5 If playback does not start automatically, press the PLAY/▲ button to start playback. 3 4 5 Press the STOP/▼ button to stop playback. Press the REW(ind)/{ button to rewind the tape. Insert a tape in the TV/VCR. EJECT POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.
Recording 29 Read and follow the steps below to record a TV program. 1 1 Place a tape with its record tab intact (see page five) in the TV/VCR. The power will come on. Or, if the tape is already in the TV/VCR, press the POWER button to turn on the TV/VCR, if necessary. 2 3 EJECT POWER Press the SPEED button until the desired tape speed appears on the TV/VCR screen. See tape speed details below. Use the CH(annel) o/p buttons or the Number buttons to select the channel you want to record.
One-Touch Recording A One-Touch Recording (OTR) is an immediate timed recording from 30 minutes to eight hours long. Before you begin, make sure: ● Channels are set. Details are on page 10. ● A tape is in the TV/VCR. The record tab must be intact. 4 Press the STOP/EJECT button on the TV/VCR to stop the OTR. EJECT POWER 1 Use the CH(annel) o/p buttons or the Number buttons to select the channel you want to record.
Rerecording (Tape Duplication) 31 AUDIO and VIDEO OUT Jacks on source unit (VCR or Camcorder) CC13C1MG AUDIO VIDEO EARPHONE STOP R EJECT VIDEO AUDIO OUT IN Audio Cable from AUDIO OUT to AUDIO In Video Cable from VIDEO OUT to VIDEO In AUDIO and VIDEO In Jacks on TV/VCR 1 Make the connections shown above, using audio and video cables (not supplied). Connect the source unit (VCR or camcorder) to a power source after connections are made. 2 The source unit will play your tape.
Timer Recording Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears, followed by the SET CLOCK menu. Details are on pages 12-17. ● Channels are set. Details are on page 10. ● A tape is in the TV/VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program.
Timer Recording (cont’d) 33 4 Use the Number buttons (1-8) to select a position in which to store the timer recording. Flashing numbers indicate an open position (one in which a timer recording has not been stored yet). NOTE: If you select a number that already has been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen for a few seconds. Then information about the program in that position will appear on the screen. If this happens, press the STATUS/EXIT button.
Timer Recording (cont’d) 8 10 11 Press the Number 1 button to record in SP speed or press the Number 2 button to record in SLP speed. Details about tape speed are on page 29. You cannot use the SPEED button at this time.
Timer Recording (cont’d) 35 Checking or Clearing Timer Recordings 1 2 3 5 2-4 With the TV/VCR on, press the MENU button. Press the PLAY/▲ button or the STOP/▼ button to select VCR PROGRAM, then press the F.FWD/B button. Press the PLAY/▲ button or the STOP/▼ button to select PROGRAM REVIEW, then press the F.FWD/B button. The timer recording information for the program in the lowest numbered position will appear on the screen.
Defeat Recording Follow the steps below to prevent accidental recording. 4 2-3 1 Press the MENU button. EJECT POWER > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 2 1 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 Press the PLAY/▲ button or the STOP/▼ button to select VCR SETUP, then press the F.FWD/B button. REC /OTR PAUSE /STILL PLAY REW F.
Repeat Play 37 Follow the steps below to program the TV/VCR to play a tape over and over. 4 2-3 1 Press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS EJECT 1 POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 2 REC /OTR PAUSE /STILL PLAY Press the PLAY/▲ button or the STOP/▼ button to select VCR SETUP, then press the F.FWD/B button.
A-B Repeat Play Follow the steps below to program the TV/VCR to play the material between two specified points (A and B) on a tape over and over again. 1 2 1 Insert a tape in the TV/VCR. EJECT POWER Insert a tape in the TV/VCR. 2 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 Press the MENU button. SLEEP/ WAKE UP 9 ALT.CH 0 > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS REC /OTR PAUSE /STILL PLAY REW F.FWD STOP 3 CH.
A-B Repeat Play (cont’d) 39 6 Press the STATUS/EXIT button to remove the menu. A-B REPEAT will appear on the screen. Beneath it, the letter A will flash beside the real-time counter. 6 7-8 EJECT POWER A-B REPEAT A 0:12:34 7 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 Play, fast forward, or rewind the tape to the position at which you want to begin playback. Stop the tape, then press the MEMORY button to set the start position (A).
Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 3 1 Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. EJECT POWER 2 Press the STATUS/EXIT button. The real-time counter will appear on the screen. 01:08 PM CH10 2 STOP MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 REC /OTR SLP PAUSE /STILL PLAY 1 : 23 : 45 REW 3 F.
Playback Options 41 Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD/B button or the REW(ind)/{ button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/▲ button. Super High Speed Searching (LP/SLP) EJECT POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 REC /OTR PAUSE /STILL PLAY 1 During tape playback, press the F.
SmartLock SmartLock enables parents to prevent their children from watching inappropriate material on TV. SmartLock reads the ratings for programming (except for news and sports programs, unedited movies on premium cable channels, and Emergency Broadcast System signals), then denies access to programming if the program’s rating meets or exceeds the limitations you select. The ratings are defined on page 45. To block ratings, follow the steps below. 1 Press the MENU button.
SmartLock (cont’d) 43 5 7 5-6 Press the PLAY/▲ button or the STOP/▼ button to select Movie Ratings or Parental Guidelines. Then, press the F.FWD/B button. BLOCK EJECT POWER > Movie Ratings Parental Guidelines SELECT KL CHOOSE B TO END PRESS EXIT 6 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 Press the PLAY/▲ button or the STOP/▼ button to select the rating you want to block. Then, press the F.FWD/B button so that ON appears beside the rating.
SmartLock (cont’d) To change the access code, follow these steps. 6 2,4 1 Press the MENU button. > SMARTLOCK REVIEW EXIT PRIM. SETUP VCR PROGRAM VCR SETUP PRESS B 2 Press the PLAY/▲ button or the STOP/▼ button to select SMARTLOCK. Then, press the F.FWD/B button. SMARTLOCK EJECT POWER 1 5 3 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 REC /OTR PAUSE /STILL PLAY _ _ _ _ REW F.FWD Enter Your Access Code STOP 3 CH. VOL.
SmartLock (cont’d) 45 To check the SmartLock settings and see which ratings you have blocked, follow these steps. 1 Press the MENU button. EJECT POWER > REVIEW PRESS B EXIT PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION 2 1 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 9 ALT.CH 0 Press the PLAY/▲ button or the STOP/▼ button to select REVIEW. Then, press the F.FWD/B button so that the SmartLock settings appear. Ratings that are blocked will appear on the screen.
Blue Background If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted. Or, if you want to receive the weak signal, set BLUE BACKGROUND to OFF. When you select a channel that is receiving a weak signal, you will see and hear the static in the TV programming. To set BLUE BACKGROUND to ON or OFF, follow the steps below. 1 Press the MENU button.
Sleep Timer 47 Use the sleep timer to program the TV/VCR to shut off in a certain amount of time. 1 Press the SLEEP/WAKE UP button. EJECT TO ADJUST PRESS s / B POWER –TIMER– > SLEEP OFF WAKE UP ON-TIME 2 o button or the STOP/p p button to select Press the PLAY/o SLEEP. Then press the REW(ind)/s button or the F.FWD/B button to select 30 MIN(utes), 60 MIN(utes), 90 MIN(utes), or 120 MIN(utes). (You can not set the sleep timer during a recording.
Wake Up Timer The Wake Up Timer turns on the TV/VCR automatically at a specified time within the next 24 hours. You may set the TV/VCR to turn on at a TV channel (the channel at which the TV/VCR was set last) or with VCR playback. To set the Wake Up Timer, follow the steps below. Before you begin: ● Set the clock. If the clock is not set, CLOCK MUST BE SET will appear on the screen after you select WAKE UP at step 2. Then the SET CLOCK menu will appear. Details are on pages 12-17.
Volume Bar 49 Usually, the volume bar appears when you press the VOL(ume) o/p buttons. If you do not need it, set the VOLUME BAR to OFF. For example, when you watch a program that is being broadcast with closed captions, you may choose to set the VOLUME BAR to OFF so the captions can remain on the screen. The captions will remain on the screen even when you press the VOL(ume) o/p buttons or the MUTE button. 4 2-3 EJECT POWER 1 1 Press the MENU button. > PRIM.
Closed Caption When you watch a program that has closed captions, you can access on-screen boxes containing the program’s dialogue (for example, what a character is saying), dialogue in a foreign language, or information (such as a channel guide, schedule, or announcements). Follow the steps below to select closed captions. Not all TV programs and commercials have closed captions. Similarly, all types of closed captions (second language, half-screen text, etc.) are not always broadcast.
Closed Caption (cont’d) 51 4 Press the STATUS/EXIT button. The type of closed captions you selected at step 3 will appear on the screen. EJECT POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 SLEEP/ WAKE UP 4 9 ALT.CH 0 REC /OTR PAUSE /STILL PLAY HELLO REW Standard Closed Captions F.FWD STOP CH. VOL.
Automatic Operation Features The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab intact. If a timer recording is set and the TV/VCR power is off, the TV/VCR will eject the tape if the record tab is missing.
Glossary 53 AUDIO In Jack: jack on the front of the TV/VCR which is used to record audio from another source. Automatic Channel Setup: process in which the TV/VCR memorizes all available channels. Then, when you push the CH(annel) o/p buttons, you only scan through channels you receive. Bands: settings that allow you to tune channels. • Antenna – VHF (very high frequency; channels 2-13) and UHF (ultra high frequency; channels 14-69). • Cable – all standard channels can be received without a Cable Box.
Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is on the back of the product. Also, please take a moment to identify the problem you are having, and be prepared to explain this to the representative.
Helpful Hints (cont’d) 55 The remote control is not available, or the remote control will not access the menu. • Use the buttons on the front of the TV/VCR to access the menu. You can not enter numbers (for example, to program a timer recording) using the front panel buttons. Details are on page 20. TV/VCR has no power. • Connect the power plug to an AC (alternating current) outlet completely. TV/VCR power shuts off after 15 minutes.
Specifications General CRT: 13-inch in line gun (CC13C1MG) 19-inch in line gun (CC19C1MG) Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.67 mm/sec. SLP: 11.12 mm/sec.
Limited Warranty 57 TV/VCR COMBINATION 90 Days Free Labor/One Year Free Parts Exchange (Two Years Free Exchange on Color Picture Tube) This product must be carried in for repair. WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product.
Index a-b repeat play . . . . . . . . .38-39 accessories . . . . . . . . . . . . . . .60 ant(enna) jack . . . . . . . . . . .6, 21 audio in jack . . . . . . . . .7, 20, 31 automatic playback . . . . . . . . . . . . . . .52 rewind . . . . . . . . . . . . . . . .52 batteries . . . . . . . . . . . . . . . . . .5 blue background . . . . . . . . . . .46 brightness, adjusting . . . . .24-25 memory button . . . . . . . . . . .23, 39-40 real-time counter . . . . . . . .40 rewind, power off . . . . . . .
SUPPLIED ACCESSORIES The following items are supplied with your TV/VCR; they are provided to help you use or set up your TV/VCR. Remote Control for CC13C1MG and CC19C1MG 4835 218 37311 Two AA Batteries 4835 138 17012 OPTIONAL ACCESSORIES The following additional items are not provided with your TV/VCR, but they are designed for use with your new TV/VCR. To order these optional accessories, contact us at: Philips Parts & Accessories Marketing Department 401 East Old Andrew Johnson Highway P.O.