User's Manual

IMPORTANT:
1 2 3
Please read this manual before using the unit to ensure safe and proper use.
 The unit will generate the magnetic/electric field; never place any medical equipment;
watches; credit card; magnetic record card or any magnetic sensitive products close
to the unit.
 Only phones which can support wireless charging can be recharged by this unit. For details,
please refer the user’s manual of your phone.
 The design of the unit is indoor use. Never spill or spray any type of liquid on the product.
 Do not use this product near water and moisture, for example: near a bathtub, washbowl,
kitchen sink or laundry tub; in a wet basement; or near a swimming pool.
 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
 Clean only with dry cloth. Unplug this product from external USB Charging Devices before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
 Do NOT place any heavy object on the Charging Surface. It may damage the unit.
 When replacement parts are required, be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original
parts. Unauthorized substitutions may result in fire or electric shock or other hazards.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
 Consult the dealer or an experienced radio/TV technician for help.
This equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. Modifications not authorized by the manufacturer may void user’s authority
to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
1. Phone Wireless Charging Surface
2. Watch Charging Slot(need to install the Watch Charger)
3. TWS Earphone Charging Surface
4. LED Indicator
5. Type C USB Port(For Charging only)
6. Full size USB Port(For Watch Charger only)
FCC NOTICE: LOCATION OF CONTROLS:
FCC WARNING:
1
2
3
4
3
5
4
6
4. Connect the Watch charging cable (not included) to the full size USB port on the side of the
unit.
Install the Watch Charger (not included) into the Watch Charging Slot and then place your
Watch onto the center of the charging surface as illustrated below.
(Note: If the location of the device is incorrect, charging will NOT proceed.)
5. Wait until your device finished charging as usual (the full charging indicators appear on your
de
vice display).
Notes:
1. To charge a cell phone or TWS earphone with this Charger, the cell phone or TWS earphone
must supp
ort Qi standard wireless charging.
2. During charging, if the cell phone or TWS earpone has a cover or case, it may disturb or
pr
event the wireless charging function.
3. The charging transmission distance of the unit is up to 5mm, the thickness of cell phone
c
over or case can NOT extend 5 mm.
4. To maximize the charging speed, using the USB Wall Charger (included) equipped with USB-Power
D
elivery 30W.
5. Back of phone must be void of attachments or accessories to charge wirelessly.
6. To save energy, disconnect the Charger from the USB Wall Charger if not using it for an extended
p
eriod of time.
1. Connect the Type C USB Plug from the supplied Type C USB connection cable to the Typ
e C USB
P
ort on the unit and then connect the Type C USB Plug to the Type C USB Port on your Typ
e C
Wall Charger (included) as illustrated below:
2. The blue Indicator on the unit will illuminate, and then turn to green.
3. Place your cell phone or TWS earphone onto the center of the charging surface as illustrated below
un
til the Blue LED Indicator illuminate (or the charging icon appears on the device’s display) to start
char
ging.
Input:
Output:
Transmission Distance:
1 x Owner’s Manual
1 x 3ft USB C to USB C Power Cord
1 x 30W Type C PD Wall Charger
DC 5V 3A or 9V 3A or 12V 2.5A or 15V 2A
2.5W (USB port) + 3W (earphone charging surface) + 15W
(Phone charging surface) (Total 20.5W)
Up to 5 mm
GENERAL SPECIFICATION:OPERATION:
ACCESSORIES:
MCH3368 IM
Size: 144mm x 195mm
5
6
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE
MODEL: MCH3383C