FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
LOCATION OF CONTR0LS MAN UNIT: Front: 1. Remote Receiver 2. LED Display 3. VOLUME Control Knob 4. (（Disc Tray Open-Close)/(Standby) Button 5. I◄◄ (Skip backward/Radio program down) Button 6. ►►I (Skip forward/Radio program up) Button 7. AUX (In) Jack 8. CD Disc Tray 9. ►II/PP (Play-Pause/Radio Program Preset) Button 10. ■/ (Stop/Decorative Lights On-Off) Button 11. MODE Button 12.
Rear: 1. FM ANT (Antenna) 2. POWER Switch 3. DC 15V (In) Jack 4. Speaker R (right) Clips 5.
REMOTE CONTROL: 1. (Standby) Button 2. Numeric Buttons 3. PROG (Program) Button 4. ◄◄ (Fast rewind/Radio tuning down) Button 5. I◄◄ (Skip backward/Radio program down) Button 6. REP (Repeat) Button 7. ►II/PP (Play-Pause/Radio Program Preset) Button 8. 9. (Disc Tray Open/Close) Button 5+ Button 10. MODE Button 11. ■ (Stop) Button 12. (Mute) Button 13. ►► (Fast forward/Radio tuning up) Button 14. VOL + (Volume Up ) Button 15. ►►I (Skip forward/Radio program up) Button 16.
CONNECTION: Connect the Speaker Connection Wires from Speaker Boxes to Speaker Out Clips on the rear of unit as illustrated below: 9
POWER SOURCE: Main unit: Connect the small plug from the supplied AC/DC Adaptor to the DC 15V (In) Jack on the rear of unit then plug the AC/DC Adaptor to a AC wall outlet having AC 100-240V~; 50/60Hz as illustrated below: NOTES: If you will not use the unit for an extended period of time, unplug the AC/DC Adaptor from wall outlet. The AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position.
Remote Control: First time use: Remove and discard the insulation film as illustrated below: Replacing the button cell when it is drained as follows: Push and slide out the button cell holder as illustrated below. Replace the button cell with new CR2025 button cell with the polarity markings on the rear of the Remote Control. Close the button cell holder. Battery precautions: Follow these Battery Precaution when using a battery in this device: 1.
6. Do not dispose of battery in fire. Battery may explode or leak. 7. Clean the battery contacts and also those of the device prior to battery installation. 8. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burn in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
OPERATION: GENERAL OPERATION: 1. Connect the Speaker Boxes to the unit as previously instructed. 2. Connect the unit to AC power as previously instructed. 3. Slide the POWER Switch to ON position to power on the unit to standby mode. "O" will appear on the display. 4. Press and hold the (Standby) Button on the unit or press the button on the Remote Control to power on the unit from standby mode. 5. Press the MODE Button on the Unit or Remote Control repeatedly to switch to desired playback mode.
7. When finished listening, press and hold the press the (Standby) Button on the unit or button on the Remote Control to turn the unit to Standby Mode. NB: If you will not use the unit for an extended period of time, slide the POWER Switch to OFF position to power off the unit then unplug the AC/DC Adaptor from AC wall outlet. CD: CD Playback: 1. Power on the unit as previously instructed. 2. Press the MODE Button on the Unit or Remote Control repeatedly until “Cd” appear on the display. 3.
2. Select the first specific track to be programmed by pressing the I◄◄ or ►►I buttons on the unit or Remote Control repeatedly. 3. Press the PROG Button again to store the selected track into the memory. 4. Repeat steps 2 and 3 until all the specific tracks stored into the memory. 5. Press the ►II/PP Button on the unit or Remote Control to start program playback. 6. To stop playback, press the ■ Button on the unit or Remote Control. Press the ►II/PP Button to start program playback again. 7.
3. Wait a few seconds until the unit is automatically paired to the external BT Device. The indicator “bt” on the display will stop blinking. 4. After pairing is complete you may now play music with your external BT Device. FM RADIO: 1. Power on the unit as previously instructed. 2. Press the MODE Button on the Unit or Remote Control repeatedly indicator “rAdI0” appear on the display to enter to Radio FM playback mode. Wait a few seconds, radio frequency “XX.XX MHz” will appear on the display. 3.
AUX (AUX/LINE IN): Listen from an external Audio Player such as a Cell phone, MP3 Player, Discman …etc. 1. Connect one end of the Audio Connection Cable (not included) to the AUX Out/Line Out/Phone Jack on the external Audio Player. 2. Connect the other end of the cable to the AUX (Aux/Line In) Jack on the front of unit as illustrated below: 3. Power on the unit as previously instructed. 4. Press the MODE Button on the Unit or Remote Control repeatedly until “AUH” appear on the display. 5.
USB: To play the music in external USB Device: 1. In standby mode, insert the USB Device into the USB Port on the front of unit as illustrated below: 2. Power on the unit as previously instructed. 3. Press the Mode Button on the Unit or Remote Control repeatedly until “USb” appear on the display to enter to USB playback mode. 4. Wait a few seconds, the unit will automatically play the first track on the USB Device. Note: If no USB Device was inserted into the USB Port.
Use the Numeric & 5+ buttons on the Remote Control to select and plays the desired tracks. For examples: To play the 4th track on the USB device, press the “4” Button. “0004” will appear on the display then the unit will start to play it. To play the 14th track on the USB device, press the “5+” + “5+” + “4” buttons. “0014” will appear on the display then the unit will start to play it. Notes: Up to 64 GB USB Device the unit supports to play.
Volume level too high Reduce the volume level by turning the VOLUME Control Knob on the unit counterclockwise or press the VOL – Button on Sound distortion the Remote Control Volume level of the Reduce the volume level connected/paired device too of the connected/paired high device Unit not in BT mode Press the MODE Button on the Unit or Remote Control repeatedly until indicator “bt” appear on the display and blink to enter to BT playback BT not functioning mode The external BT Device had Pair
Radio reception not good The direction or location no Unwind and extended the good for radio reception FM wire antenna on the rear of unit to its full length and/or reassemble the other direction/location to improve the reception USB Device not function Unit is not in USB mode Press the MODE Button on the Unit or Remote Control repeatedly until “USb” appear on the display to enter to USB playback mode No audio files on the USB Download the desired Device music in MP3 format into the USB Device be
