TVCR CC13B1MG CC19B1MG Color TV with built-in VCR Owner’s Manual
Return your Warranty Registration Card today to ensure you receive all the benefits you’re entitled to. Once your purchase is registered, you’re eligible to receive all the privileges of owning this product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 Welcome to your TV/VCR owner’s manual. This manual describes two models: CC13B1MG and CC19B1MG. Although the models may have a different appearance, both models operate exactly the same. The features described in this manual apply to both models unless otherwise specified. The CC13B1MG is illustrated in this manual, but the CC19B1MG has a similar appearance.
Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hooking Up the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 1 2 2 3 3 Remove the battery compartment lid on the bottom of the remote control by sliding it in the direction of the arrow. Place two AA batteries inside the battery compartment with their + and – ends aligned as indicated. Replace the battery compartment lid. Recording Prevention Video cassette tapes have record tabs to ensure that recordings are not accidentally erased.
Hooking Up the TV/VCR 1 Hook up your TV/VCR using one of the connections shown. A. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna Connect a Cable signal or an antenna to the ANT(enna) Jack. ANT. ANT. B. Hooking Up Your TV/VCR With a Cable Box To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box. Connect the Cable signal to the IN Jack on the Cable Box.
Hooking Up the TV/VCR (cont’d) 7 D. Hooking Up Your TV/VCR to Another Video Source (VCR or Camcorder) You may need this connection if you want to copy tapes. Details are on page 31. AUDIO/VIDEO OUT Jacks on VCR 3CH 4CH AUDIO VIDEO OUT IN Use an Audio cable to connect the AUDIO OUT Jack on the VCR to the AUDIO In Jack on the front of the TV/VCR. IN ANT. OUT AUDIO VIDEO AUDIO VIDEO EARPHONE 3CH 4CH AUDIO VIDEO OUT IN STOP REW EJECT PLAY F.FWD REC OTR CHANNEL VOLUME POWER IN ANT.
Turning On the TV/VCR Before you turn on the TV/VCR, make sure batteries are in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button. The TV/VCR will come on and the screen shown below will appear. SELECT LANGUAGE > ENGLISH ON ESPAÑOL SELECT KL OR PRESS MENU TO CONTINUE 3 1 5 POWER MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CLEAR MEMORY CHANNEL ALT.
Language Selection 9 2-4 Follow the steps below to change the language of the on-screen displays and menus. 1 Press the MENU button. PRESS B > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 2 5 1 POWER MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the FF/SEARCH/B button. PRIMARY SETUP CLEAR MEMORY CHANNEL ALT.
Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. 2-3 1 Press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 1 2 POWER MENU 1 2 3 4 5 6 7 8 9 Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP, then press the FF/SEARCH/B button. STATUS/EXIT 0 CLEAR MEMORY CHANNEL ALT.
Automatic Channel Setup (cont’d) 11 Adding/Deleting Channels 1 Press the MENU button. TO ADJUST PRESS { / B CH123 SAVED > CHANNEL SMARTLOCK REVIEW EXIT PRIM. SETUP VCR PROGRAM 1 2 Press the PLAY/▲ button or the STOP/▼ button to select CHANNEL. TO ADJUST PRESS { / B CH123 SAVED > CHANNEL SMARTLOCK REVIEW EXIT PRIM. SETUP VCR PROGRAM POWER MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 4 2 CLEAR 5 MEMORY CHANNEL ALT.
Setting the Clock There are three ways to set the clock: Manually, with Automatic PBS Channel Selection, or with Manual PBS Channel Selection. With manual clock setting, you tell the TV/VCR the current time. With Automatic or Manual PBS Channel Selection, the TV/VCR gets the time from your local PBS station. If you use either Manual PBS Channel Selection or Automatic PBS Channel Selection, follow the steps on page 19 to have the TV/VCR maintain the clock according to your Time Zone.
Setting the Clock (cont’d) 13 4 Press the PLAY/▲ button or the STOP/▼ button to select SET MANUAL CLOCK, then press the FF/SEARCH/B button. SET MANUAL CLOCK TIME – – : – – DATE – – / – – / – – – – TO END PRESS EXIT 5 SET MANUAL CLOCK TIME MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
Setting the Clock (cont’d) Automatic PBS Channel Selection 1 Press the MENU button. > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 1,4 PRESS B 2 Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the FF/SEARCH/B button. PRIMARY SETUP > SELECT LANGUAGE AUTO PROGRAMMING CH MEMORY REVIEW VOLUME BAR [ON] SET CLOCK SELECT KL CHOOSE B TO END PRESS EXIT 3 POWER MENU 1 2 STATUS/EXIT 3 4 5 6 7 8 9 0 CLEAR MEMORY CHANNEL ALT.
Setting the Clock (cont’d) 15 5 Press the PLAY/▲ button or the STOP/▼ button to select SET PBS CH. AUTO. Then, press the FF/SEARCH/B button. 6 Wait for the TV/VCR to find the time. SET AUTO CLOCK TIME ––:–– DATE ––/––/–––– NOW SEARCHING TO END PRESS EXIT 6 7 NOW SEARCHING flashes on the TV/VCR screen. 7 POWER MENU 1 2 STATUS/EXIT 3 4 5 6 7 8 9 0 CLEAR MEMORY CHANNEL ALT.CH SLEEP/WAKE UP When the TV/VCR finds the PBS channel, the time will appear on the screen.
Setting the Clock (cont’d) Manual PBS Channel Selection 1 Press the MENU button. > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 1,4 PRESS B 2 Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the FF/SEARCH/B button. PRIMARY SETUP > SELECT LANGUAGE AUTO PROGRAMMING CH MEMORY REVIEW VOLUME BAR [ON] SET CLOCK SELECT KL CHOOSE B TO END PRESS EXIT POWER MENU 1 2 STATUS/EXIT 3 4 5 6 7 8 9 0 CLEAR MEMORY CHANNEL ALT.
Setting the Clock (cont’d) 17 5 Press the PLAY/▲ button or the STOP/▼ button to select SET PBS CH. MANUAL. Then, press the FF/SEARCH/B button. 7 Wait for the TV/VCR to find the time. AUTO CLOCK (PBS) CH 02 TIME ––:–– DATE ––/––/–––– SELECT CHANNEL NUMBER TO END PRESS EXIT 6 Use the Number buttons to select your PBS station. AUTO CLOCK (PBS) CH 12 TIME ––:–– DATE ––/––/–––– 8 6 POWER MENU 1 2 STATUS/EXIT 3 4 5 6 7 8 9 0 CLEAR MEMORY CHANNEL ALT.
Daylight-Savings Time When the Daylight-Savings Time feature is ON, the TV/VCR clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October. To turn Daylight-Savings Time ON or OFF, follow the steps below. 1 Press the MENU button. > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 2-4 5 1 POWER MENU 1 2 STATUS/EXIT 3 4 5 6 7 8 9 0 2 CHANNEL ALT.
Time Zone 19 When you set the clock using AUTO CLOCK, specify your time zone. The TV/VCR will maintain the clock according to your time zone. 1 2-5 Press the MENU button. > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 2 Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the FF/SEARCH/B button.
Front Panel Cassette Compartment Insert a video cassette tape here. Wireless Remote Sensor Receives a signal from your remote control so you can operate the TV/VCR from a distance. STOP/EJECT Button Press once to stop the tape. When playback is stopped, press to eject the tape. Press to select an item in the menu. VIDEO In Jack Connect this jack to the video out jack of a camcorder or a VCR. Details are on page 31. AUDIO In Jack Connect this jack to the audio out jack of a camcorder or a VCR.
Rear Panel 21 ANT. AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR. ANT(enna) Jack Connect your antenna or cable here. Details are on pages six-seven. Antenna Hole Connect the stem of an indoor antenna here. Details are on page six.
Remote Control Buttons CLEAR Button Press to erase incorrect data when programming TV/VCR functions. Also, press to reset the real-time counter to 0:00:00. Details are on page 40. STATUS/EXIT Button Press to see the status display. Press again to remove the status display. Details are on page 26. Press to exit the menu. MENU Button Press to display the pop up menu. You also may use the buttons on the front panel of the TV/VCR to access the pop up menu. Details are on page 20.
Remote Control Buttons (cont’d) 23 CHANNEL ▲/▼ Buttons Press to scan through the TV/VCR’s channels. MEMORY Button Press to memorize a tape position at which the real-time counter was set to 0:00:00. Details are on page 40. Or, press to memorize the start and end positions on a tape when setting up A-B Repeat Play. Details are on pages 38-39. ALT. CH (Alternate Channel) Button Press to return to the TV channel you were viewing immediately before switching to your current channel.
Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 1 Press the MENU button. K > BRIGHTNESS PICTURE COLOR TINT SHARPNESS TV RESET K TO ADJUST PRESS { / B 2 3 4 1 POWER MENU 1 2 STATUS/EXIT 3 4 5 6 7 8 9 0 CHANNEL ALT.CH Press the PLAY/▲ button or the STOP/▼ button to select the desired control (BRIGHTNESS, for example). Press the REW(ind)/SEARCH/{ button or the FF/SEARCH/B button to adjust the control.
Adjusting the Picture Controls (cont’d) 25 Decrease decreased brightness decreased contrast paler more purple softer BRIGHTNESS PICTURE COLOR TINT SHARPNESS Increase increased brightness increased contrast more brilliant more green clearer Press the REW(ind)/SEARCH/{ button to decrease a picture control. Press the FF/SEARCH/B button to increase a picture control. PLAY F.
On-Screen Status Displays A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below. If you select STATUS ON, then select COUNTER ONLY OFF: ● Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the status display also may appear when you press other function buttons.
Reminder 27 The channel number will remain on the screen at all times when you set REMINDER to ON. The exceptions are during tape playback or when closed captioning is selected. Set REMINDER to ON or OFF by following the steps below. 1 1 Press the MENU button. TO ADJUST PRESS { / B > REMINDER OFF BRIGHTNESS PICTURE COLOR TINT SHARPNESS Press the PLAY/▲ button or the STOP/▼ button to select REMINDER.
Playing Follow the steps below to play a tape. 1 Insert a tape in the TV/VCR. The power will come on. If the tape’s record tab has been removed, playback should start automatically. 1 5 Insert a tape in the TV/VCR. Press the STOP/EJECT button on the TV/VCR. 2 If playback does not start automatically, press the PLAY/▲ button to start playback. 3 Press the STOP/▼ button on the remote control or the STOP/EJECT button on the TV/VCR once to stop playback.
Recording 29 Read and follow the steps below to record a TV program. 1 Place a tape with its record tab intact (see page five) in the TV/VCR. The power will come on. Or, if the tape is already in the TV/VCR, press the POWER button to turn on the TV/VCR, if necessary. 2 Press the SPEED button until the desired tape speed appears on the TV/VCR screen. Details about tape speed are given below.
One-Touch Recording The One-Touch Recording (OTR) function allows you to program an immediate timed recording from 30 minutes to eight hours long without setting the timer. Before you begin, make sure: ● Channels are set up. ● There is a tape in the TV/VCR. The record tab must be intact. 4 Press the STOP/EJECT button on the TV/VCR to stop the OTR. 1 Use the CHANNEL ▲/▼ buttons or the Number buttons to select the channel you want to record.
Rerecording (Tape Duplication) 31 AUDIO and VIDEO OUT Jacks on source unit (VCR or Camcorder) AUDIO VIDEO EARPHONE STOP R EJECT VIDEO AUDIO OUT IN Audio Cable (white) from AUDIO OUT to AUDIO In Video Cable (yellow) from VIDEO OUT to VIDEO In AUDIO and VIDEO In Jacks on TV/VCR 1 Make the connections shown above, using audio and video cables. Connect the source unit (VCR or camcorder) to a power source after connections are made. 2 The source unit will play your tape.
Timer Recording Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears, followed by the SET CLOCK menu. ● Channels are set up. ● There is a tape in the TV/VCR. (Make sure the tape’s record tab is intact and the tape is long enough to record the program.
Timer Recording (cont’d) 33 4 Use the Number buttons (1-8) to select a position in which to store the timer recording. Flashing numbers indicate an open position (one in which a timer recording has not been stored yet). NOTE: If you select a number that already has been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen for a few seconds. Then information about the program in that position will appear on the screen. If this happens, press the STATUS/EXIT button.
Timer Recording (cont’d) 8 Press the Number 1 button to record in SP speed or press the Number 2 button to record in SLP speed. Details about tape speed are on page 29. You cannot use the SPEED button at this time. 11 10 ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON 09:30 PM TIME OFF 11:00 PM REC SPEED SLP SP=1 SLP=2 TO CORRECT PRESS CLEAR TO END PRESS EXIT 9 Press two Number buttons for the month and two Number buttons for the day you want the program to record.
Timer Recording (cont’d) 35 Checking or Clearing Timer Recordings 1 2 3 2-3 With the TV/VCR on, press the MENU button. Press the PLAY/▲ button or the STOP/▼ button to select VCR PROGRAM, then press the FF/SEARCH/B button. Press the PLAY/▲ button or the STOP/▼ button to select PROGRAM REVIEW, then press the FF/SEARCH/B button. The timer recording information for the program in the lowest numbered position will appear on the screen.
Defeat Recording Follow the steps below to prevent accidental recording. 1 Press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 4 1 2 2-3 POWER MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CLEAR MEMORY CHANNEL ALT.CH Press the PLAY/▲ button or the STOP/▼ button to select VCR SETUP, then press the FF/SEARCH/B button.
Repeat Play 37 Follow the steps below to program the TV/VCR to play a tape over and over. 1 Press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 2 4 1 2-3 POWER MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 Press the PLAY/▲ button or the STOP/▼ button to select VCR SETUP, then press the FF/SEARCH/B button. VCR SETUP > ONE TIME PLAY [ON] REPEAT PLAY ON-SCREEN MODE DEFEAT RECORDING [OFF] BLUE BACKGROUND [ON] CLEAR MEMORY CHANNEL ALT.
A-B Repeat Play Follow the steps below to program the TV/VCR to play the material between two specified points (A and B) on a tape over and over again. 1 2 1 Insert a tape in the TV/VCR. Insert a tape in the TV/VCR. Press the MENU button. > PRIM. SETUP 2 POWER MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 CLEAR MEMORY PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 0 CHANNEL ALT.
A-B Repeat Play (cont’d) 39 6 7-8 Press the STATUS/EXIT button to remove the menu. A-B REPEAT will appear on the screen. Beneath it, the letter A will flash beside the real-time counter. . 6 A-B REPEAT A 0:12:34 7 Play, fast forward, or rewind the tape to the position at which you want to begin playback. Stop the tape, then press the MEMORY button to set the start position (A). The flashing A will become a flashing B.
Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 1 Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. 2 2 POWER MENU 1 2 3 4 5 6 7 8 9 Press the STATUS/EXIT button. The real-time counter will appear on the screen. 01:08 PM CH10 STOP STATUS/EXIT 0 CLEAR MEMORY CHANNEL 3 4 ALT.
Playback Options 41 Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the FF/SEARCH/B button or the REW(ind)/SEARCH/{ button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/▲ button. POWER MENU 1 2 3 4 5 6 7 8 9 Super High Speed Searching (LP/SLP) 1 During tape playback, press the FF/SEARCH/B button or the REW(ind)/SEARCH/{ button, then press again. The TV/VCR will now search in super high speed.
SmartLock SmartLock enables parents to prevent their children from watching inappropriate material on TV. SmartLock reads the ratings for programming (except for news and sports programs, unedited movies on premium cable channels, and Emergency Broadcast System signals), then denies access to programming if the program’s rating meets or exceeds the limitations you select. The ratings are defined on page 45. To block ratings, follow the steps below. 1 Press the MENU button.
SmartLock (cont’d) 43 5-6 5 Press the PLAY/▲ button or the STOP/▼ button to select Movie Ratings or Parental Guidelines. Then, press the FF/SEARCH/B button. BLOCK 7 > Movie Ratings Parental Guidelines SELECT KL CHOOSE B TO END PRESS EXIT 6 Press the PLAY/▲ button or the STOP/▼ button to select the rating you want to block. Then, press the FF/SEARCH/B button so that ON appears beside the rating. For example, if you set PG to ON, you may not view PG programming because the block is on.
SmartLock (cont’d) To change the access code, follow these steps. 1 Press the MENU button. > SMARTLOCK REVIEW EXIT PRIM. SETUP VCR PROGRAM VCR SETUP PRESS B 2 Press the PLAY/▲ button or the STOP/▼ button to select SMARTLOCK. Then, press the FF/SEARCH/B button. SMARTLOCK _ _ _ _ Enter Your Access Code 3 6 1 5 3 2,4 POWER MENU 1 2 STATUS/EXIT 3 4 5 6 7 8 9 0 CLEAR MEMORY CHANNEL ALT.
SmartLock (cont’d) 45 To check the SmartLock settings, follow these steps. 1 Press the MENU button. > REVIEW PRESS B EXIT PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION 1 2 Press the PLAY/▲ button or the STOP/▼ button to select REVIEW. Then, press the FF/SEARCH/B button so that the SmartLock settings appear. Ratings that are blocked will appear on the screen. An “X” will appear if a specific sub-rating is blocked, such as V for Violence in the TV-14 category.
Wake Up Timer The Wake Up Timer turns on the TV/VCR automatically at a specified time within the next 24 hours. You may set the TV/VCR to turn on at a TV channel (the channel at which the TV/VCR was set last) or with VCR playback. To set the Wake Up Timer, follow the steps below. Before you begin: ● Make sure the clock is set. If the clock has never been set, CLOCK MUST BE SET will appear on the screen after you select WAKE UP at step 2. Then the SET CLOCK menu will appear.
Sleep Timer 47 Use the Sleep Timer to program the TV/VCR to shut off in a certain amount of time. 1 Press the SLEEP/WAKE UP button. B TO ADJUST PRESS s/B –TIMER– > SLEEP OFF WAKE UP ON-TIME 2 o button or the STOP/p p button to select Press the PLAY/o SLEEP. Then press the REW(ind)/SEARCH/s button or the FF/SEARCH/B button to select 30 MIN(utes), 60 MIN(utes), 90 MIN(utes), or 120 MIN(utes). (You can not set the Sleep Timer during a recording.
Closed Caption When you watch a program that is being broadcast with closed captions, you can access on-screen boxes containing the program’s dialogue (for example, what a character is saying), dialogue in a foreign language, or information (such as a channel guide, schedule, or announcements). Follow the steps below to select closed captions. Not all TV programs and commercials are broadcast with closed captions. Similarly, all types of closed captions (second language, half-screen text, etc.
Closed Caption (cont’d) 49 4 Press the STATUS/EXIT button. The type of closed captions you selected at step 3 will appear on the screen. POWER MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 CLEAR 4 MEMORY HELLO Standard Closed Captions 0 CHANNEL ALT.
Blue Background If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted. Or, if you want to receive the weak signal, set BLUE BACKGROUND to OFF. When you select a channel that is receiving a weak signal, you will see and hear the static in the TV programming. To set BLUE BACKGROUND to ON or OFF, follow the steps below. 1 Press the MENU button. > PRIM.
Volume Bar 51 Usually, the volume bar appears when you press the VOLUME ▲/▼ buttons. If you do not need it, set the VOLUME BAR to OFF. For example, when you watch a program that is being broadcast with closed captions, you may choose to set the VOLUME BAR to OFF so the captions can remain on the screen. The captions will remain on the screen even when you press the VOLUME ▲/▼ buttons or the MUTE button. 1 Press the MENU button. > PRIM.
Automatic Operation Features The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab intact. If a timer recording is set and the TV/VCR power is off, the TV/VCR will eject the tape if the record tab is missing.
Specifications 53 General CRT: 13-inch in line gun (CC13B1MG) 19-inch in line gun (CC19B1MG) Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.67 mm/sec. SLP: 11.12 mm/sec.
Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is displayed on the back of the product. Also, please take a moment to identify the problem you are having, and be prepared to explain this to the representative.
Helpful Hints (cont’d) 55 The remote control is not available, or the remote control will not access the pop up menu. • Use the buttons on the front panel of the TV/VCR to access the pop up menu. You can not enter numbers (for example, to program a timer recording) using the front panel buttons. Details are on page 20. TV/VCR power shuts off after 15 minutes.
Glossary AUDIO In Jack: jack located on the front of the TV/VCR which is used to record audio from another source. Automatic Channel Setup: process in which the TV/VCR scans all available channels and places the ones you receive in its memory. Then, when you push the CHANNEL o/p buttons, you only scan through channels you receive. Bands: settings that allow you to tune channels. • Antenna – VHF (very high frequency; channels 2-13) and UHF (ultra high frequency; channels 14-69).
Limited Warranty 57 TV/VCR COMBINATION 90 Days Free Labor/One Year Free Parts Exchange (Two Years Free Exchange on Color Picture Tube) This product must be carried in for repair. WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product.
Index a-b repeat play . . . . . . . . .38-39 accessories . . . . . . . . . . . . . . .60 ant(enna) jack . . . . . . . . . . .6, 21 audio in jack . . . . . . . . .7, 20, 31 automatic playback . . . . . . . . . . . . . . .52 rewind . . . . . . . . . . . . . . . .52 batteries . . . . . . . . . . . . . . . . . .5 blue background . . . . . . . . . . .50 brightness, adjusting . . . . .24-25 memory button . . . . . . . . . . .23, 38-40 real-time counter . . . . . . . .40 rewind, power off . . . . . . .
SUPPLIED ACCESSORIES The following items are supplied with your TV/VCR; they are provided to help you use or set up your TV/VCR. POW ER MEN U 1 STAT US/E XIT 2 4 CLEA R 3 5 MEM 7 ORY 6 8 9 CHA 0 NNE L ALT.