Manual

23
Timer Recording (cont'd)
8 11
Press the Number 1 button to record in
SP speed, press the Number 2 button to
record in LP speed, or press the
Number 3 button to record in SLP
speed. For details, see page five. You
cannot use the (Tape) SPEED button at
this time.
,_E TIME PfiOGRAM 1
PROGRAM I
CHANNEL 10
TIME ON 09:30 PM
TIME OFF 11:00 PM
TO CORRECT PUSH CLEAR
_LomDPushEXiT
9
Press two Number buttons for the
month and two Number buttons for the
day you want to record the program.
For example, for July 10, 1996, press
07, 10. The day of the week and the
year will be displayed automatically
(you cannot program the VCR to
record more than one year in advance).
-_._TO/*_ETOlIME OFFTfMESTARTRECCHANNELPROGRAMCORRECTENDTIMESPEEDONPUSHDATEPROGRAMPUSHEXITWED07/I0_6SLP11:00PM09:30101CLEARPM 1
10
Press the STATUS/EXIT button.
PROGRAM WAS COMPLETED /
PLEASE TURN OFF VCR FOR
TIMER RECORDING will appear on-
screen (if PROGRAM NOT COM-
PLETED appears, try again from step
1). In three seconds, the on-screen dis-
play will disappear. Now, go to steps
11 and 12.
If you want to program another timer
recording, press the MENU button.
Repeat steps 2 - 10. If you don't want
to program another timer recording, go
to step 12.
12
Turn off the VCR power. The TIMER
light will appear. The VCR must be
turned off for a timer recording to
take place. If you forget to turn the
VCR off, PLEASE TURN OFF VCR
FOR TIMER RECORDING flashes
on your TV screen two minutes before
a timer recording starts. You can
remove the message by pressing the
CLEAR button.
The VCR
must be off for a
timer recording
to take place!
Make sure there
is a tape in the
VCR.
Making Corrections
1. If you need to make corrections while
programming a timer recording, press
the CLEAR button until the cursor is
flashing on the item you want to change.
Then enter the correct information.
2. Continue to do this until all information
is correct.
3. Press the STATUS/EXIT button to exit.
Note: You can exit the Program
review at any time by pressing the
STATUS/EXIT button.
VCR
POWER TIMER
Button Light
POWER-
Button
!STATUS/-
EXIT
Button
Number -
Buttons
886
" O
,-rn FI rsn
,'-n r-_-Ir-_
_ooo
Remote Control
CLEAR
Button
MENU
Button
• . oooio Iooo...+..e,o.Q.,+,• •,oooolel•lo • •
• CLASH mayflash on the screen
when you finish setting a timer
recording. This means that the timer
recording you just programmed and
another timer recording overlap, and
thus the current timer recording will
not be carried out.
• If the preset time for a timer record-
ing comes up during an OTR, the
OTR has priority.
• To stop a started timer recording,
press the STOP/EJECT button on
the VCR.
• If the power fails for more than one
hour, programmed timer recordings
may be lost. When you use the VCR
with the auto clock function set to
OFF, repeat the steps on page 10
before re-programming the timer
recording(s).
• lfyou are recording using a cable
converter box, leave the cable con-
verter box on while you are recording.
• Entering the TV GUIDE Plus+ sys-
tem during a recording will cancel
the recording.
Please see page 49for more notes.