Manual

7
Turning on Your VCR
°°°_°°_**°°°°°o*-°°°°°**o°°°_°°o*o°°°°°°°°°°o°_o0e_o**°°°°°o°°o****°°°°°°°ooIeeeeee*oo*eoee_I_ee*otQ°moeeeee*eeIo**e*eeeoee*oee_e_o
TV and
VCR
Set the TV to channel
3 or 4, whichever
channel the CH3/CH4
switch on the back of
the VCR is set to.
/
Press the VCR button,
then the POWER
button.
3
Press the Number 1
button for English on-
screen displays or the
Number 2 button for
Spanish on-screen dis-
plays.
€5&6
® - O
_000
00®®
®OQ®
oooo
-_ Paress the MENU
ton.
Press the CH(annel) Up
button.
Remote Control
oe • ee • oeoeee
oe • oeeoooe • eoeoo eeooeoeooeeeoeoooeeoeeooee eeeeeoeeooeoeee " eeooe
• Whenyoupress the POWER button on the VCR to turn onthe VCR_ the
remote control will beep. Press any button on the remote control to stop it.
LOCATING REMOTE will appear on-screen for almost 30 seconds. See
page 38for details.
• lfyou do not see any on-screen displays when you turn on the VCR, repeat
the steps under "Hooking Up Your VCR" on page six, then try again. If
you still do not see any on-screen displays, follow the steps under "Channel
Memory'" on page 28 and "Language Selection" on page 30.
• To skip this feature andplay a tape immediately, insert a tape with its
record tab removed. Playback will start immediately. Or, to skip step 3,
press the MENU button. All on-screen displays will be in English. To skip
step 5, press the STOP button. Channels will not be programmed, and
TUNER NOT SET will appear on-screen.
• To program channels or to change the language at a later time, follow the
steps on pages 28 and 30.
• lfyou try to program channels when there is no antenna or cable connected
to the VCR, programming will appear to take place, but eventually a NO TV
SIGNALS message will appear on-screen. Connect an antenna or cable to
the VCR and try again. You may need to follow the steps on page 28.
• You cannot program channels ifa cable converter box is connected to a
VCR that is connected to a TV. lf you have this kind of connection, see
page 44for details.
• Follow the steps on this page only when you plug the VCR power cord into
the wall outlet for the first time.
• The VCR distinguishes between standard TV channels and cable channels.
If you change to TV or CABLE TV mode, follow the steps under "Channel
Memory" on page 28.
i Before turning on your VCR, make sure
: there are batteries in the remote control and
the VCR and TV are connected (see pages
: five and six).
!1
• Turn the TV on. Set it to the same channel
: as the CH3/CH4 switch on the back of the
VCR.
2
Press the VCR button, then the POWER
button on the remote control. The VCR
light will appear on the display panel and
the language select display screen shown
below will appear.
SELECTPUSH NO, SHOWN_
1 ENGLISH ON I
2 ESPANOL /
E SELECTIONOR ]
H MENU TO CONTINUE/
Press the Number 1 button to select English
on-screen displays or the Number 2 button
to select Spanish on-screen displays.
4
Press the MENU button. The channel pro-
i gram display shown below will appear. The
i display will disappear after about 60 sec-
i onds if you do not press any buttons.
i,'_NNECT ANTENNAOR CABLE_k
I °vc"
/ THEN-. /
I uS"c"uP */
!5
: Press the CH(annel) Up button to begin auto-
•_ matic channel programming. AUTO SET
: PROCEEDING PLEASE WAIT will appear
: on-screen. The VCR will place all of the
: channels you receive into its memory, so
: when you scan through channels using the
i CH(annel) Up/Down buttons, you'll only scan
: through channels that you receive. The chan-
: nel numbers will appear briefly on the display
i panel. When all channels are programmed,
: AUTO SET COMPLETED will appear on-
screen briefly. Then the TV GUIDE Plus+ set
i up screen appears automatically. Follow the
! steps in TV GUIDE Plus+ Setup section of the
i separate TV GUIDE Plus+ manual.