Magnum Dynalab MD 107T/107TR ANALOG FM TUNER INSTRUCTION MANUAL
-2- TABLE OF CONTENTS A MESSAGE FROM THE PRESIDENT 3 UNPACKING YOUR 107T 4 SETTING UP YOUR MD 107T 5 CONTROLS AND FUNCTIONALITY 6 DISPLAYS AND METERS 7 CHECKING OUT YOUR MD 107T 8 TUNER REMOTE (OPTIONAL) 9 RC6 REMOTE IMAGE 10 TROUBLESHOOTING 11 RECEPTION TECHNIQUES 12 Antenna Cabling: 12 Types of Antennas: 12 FM RECEPTION AIDS AND ACCESSORIES 13 PRODUCT SPECIFICATIONS 14 SAFETY SHEET 15 LIMITED WARRANTY 16
-3- A Message From the President Thank you for choosing the Magnum Dynalab “MD 107T” FM Tuner. Great care has been given in the design, manufacturing and selection of components for the “MD 107T” FM Tuner. This complete process will insure that your listening experience will be optimized for years. The front end of all Magnum Dynalab tuners is an exclusive “in house” designed and manufactured component, we are the only company in the world that does their own R.F. “Front-end”.
-4- UNPACKING YOUR 107T Carefully inspect all sides of the shipping carton for damage. If there are marks or holes in the carton make note of the location in relation to the unit inside. Any obvious dents or scuff marks should alert you to the possibility of damage. Carefully remove the MD 107T from the end caps and wrapping, inspect all sides. Pay special attention to the corresponding areas on the unit where damage was found to the shipping carton.
-5- SETTING UP YOUR MD 107T 1. Place your tuner the shortest distance possible from your pre-amplifier/ integrated amplifier, being careful to avoid areas that may cause extreme temperatures. 2. Connect your tuner to the pre-amplifier, using cables/ inter-connects that are consistent with the rest of the inter-connects in your system. For a single ended (un-balanced) system the cables will be connected to the RCA connectors labeled “output to preamp” on the rear panel of your tuner to an unused aux.
-6- CONTROLS AND FUNCTIONALITY A. POWER – Turns the power (AC) on and off to your tuner, with the optional remote system this switch must be left in the “OFF” position. B. MUTE – In the “ON” position, a limit is now placed on your tuner. While scaling up and down the FM dial, weak stations will be overlooked so that no alarming noises will be heard while looking for programs. We recommend that with the optional remote system you leave the Mute switch in the “ON” position. C.
-7- DISPLAYS AND METERS H. SIGNAL STENGTH– This meter readout indicates the amount of signal the tuner is receiving, the higher the better. This will never read “100”. I. MULTI-PATH/SIGNAL METER - This meter indicates the amount of multi-path, the lower the reading the better. J. FREQUENCY/INPUT DISPLAY – Displays the station via a numeric value, the frequency that your tuner is dialed into. Display ranges from 87.5 MHz through 108.5 MHz.
-8- CHECKING OUT YOUR MD 107T 1. Place your power switch to the “ON” position (A on diagram). This should turn on your tuner’s meter lights and frequency display. 2. Place your STEREO/MONO switch (D on diagram) to the Stereo setting. 3. Place your bandwidth switch (E on diagram) to BW1. 4. Place your Mute switch (B on diagram) to “ON” position. 5. On your preamplifier/ integrated amplifier select the input that your MD 107T tuner is connected to. 6.
-9- TUNER REMOTE (OPTIONAL) If your tuner was ordered with the RC6 “PRECISION REMOTE SYSTEM”, here are the operating instructions. 1. The power switch should be off on the front panel of the tuner 2. Using the remote handheld, push the red “TUNER” button. You will see the tuner turn on. 3. To tune with the handheld, push and then hold either the “TUNE UP” or “TUNE DOWN” button until you reach the desired station. The longer you hold the button the faster the frequency changes.
- 10 - RC6 REMOTE
- 11 - TROUBLESHOOTING PROBLEM POSSIBLE CAUSE No sound, meter • Power cord lights are not on disconnected • Power off at source No sound, meter • Interconnect not lights are on properly installed • Preamp set to incorrect source • Power amplifier is off • Tube failure Low signal • Antenna not strength connected properly • Incorrect antenna Station too distant • Improper antenna position/ placement Intermittent • Mute switch is in sound the “ON” position Tuner remote • Batteries dead does not work • Butto
- 12 No sound from USB • Not compatible • Signal not receiving • Restart your computer or program • If using a MAC, you must go to “system preferences”, “sound” and select “USB DAC” RECEPTION TECHNIQUES Antenna Cabling: The lead-in cable from the antenna is often the weakest link in the FM system. Some time spent on selection and matching will yield dramatic results when it comes to noise reduction in weak signals.
- 13 - If multi-path is a reception problem try laying the antenna down in the horizontal plane rather than the vertical plane. This type of antenna can be used indoors or outdoors, but regardless of whether it is installed indoors or outdoors the higher that you can put it the better it will perform.
- 14 - PRODUCT SPECIFICATIONS Usable sensitivity- Mono – 50 dB quieting – Mono – 50 dB quieting – Stereo – Capture ratio – Image rejection – Signal to noise ratio – Alternate channel – Wide – Alternate channel – Narrow Adjacent channel – Wide – Adjacent channel – Narrow THD – Mono – THD – Stereo – Stereo separation – AM suppression – SCA rejection – IF rejection – 19 KHz and 38 KHz component rejection – Audio frequency response (+/- 1 dB) – Balanced audio output (600 ohms) Line audio output (RCA) – Line p
- 15 - SAFETY SHEET IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS DO NOT USE THIS APPARATUS IN WATER CLEAN ONLY WITH DRY CLOTH DO NOT BLOCK ANY VENTILATION OPENINGS, INSTALL IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
- 16 - LIMITED WARRANTY Register your product at www.magnumdynalab.com Magnum Dynalab Ltd. herein referred to as the “manufacturer” guarantees this product to be free of defect in both material and workmanship and agrees to remedy any such defect or replace any defective component at no charge for a period of two years from date of sale to the first end user.