90-MILLIMETER COMPATIBLE SWIPE READER TECHNICAL REFERENCE MANUAL Part Number 99831083-5 JULY 2003 REGISTERED TO ISO 9001:2000 1710 Apollo Court Seal Beach, CA 90740 Phone: (562) 546-6400 FAX: (562) 546-6301 Technical Support: (651) 415-6800 www.magtek.
Copyright© 1999-2005 MagTek®, Inc. Printed in the United States of America Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of MagTek, Inc. MagTek is a registered trademark of MagTek, Inc.
LIMITED WARRANTY MagTek warrants that the products sold to Reseller pursuant to this Agreement will perform in accordance with MagTek’s published specifications. This warranty shall be provided only for a period of one year from the date of the shipment of the product from MagTek (the “Warranty Period”). This warranty shall apply only to the original purchaser unless the buyer is authorized by MagTek to resell the products, in which event, this warranty shall apply only to the first repurchase.
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
TABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS..................................................................................... 1 CONFIGURATIONS ................................................................................................................................. 1 SPECIFICATIONS .................................................................................................................................... 1 REFERENCE DOCUMENT ....................................................
Figure 1-1.
SECTION 1. FEATURES AND SPECIFICATIONS The 90-millimeter OEM Swipe Reader has a TTL level interface and is designed for use in retail, access control, and time and attendance environments. This Reader is in compliance with industry specifications, including ANSI/ISO Standards 7810, 7811-1 through -6, 7812, 7813, and AAMVA. The Reader can be customized. Bidirectional read capability is available.
90-millimeter Compatible Swipe Reader REFERENCE DOCUMENT I/O Interface for TTL Swipe Readers, Technical Reference Manual, P/N 99875148 2
SECTION 2. INSTALLATION This section consists of installation and checkout of the Reader. MOUNTING The dimensions for mounting without the cover are shown in Figure 2-1. Figure 2-1.
90-millimeter Compatible Swipe Reader CONNECTORS Single Track I/O Connector is shown in Table 2-1, and the Dual Track I/O Connector is shown in Table 2-2. Table 2-1. I/O Connector for Single Track, 5 Pin Pin Number 1 Color Red Signal Vcc Molex 5 Pin 2 Black GND 22-01-2051 3 Orange DATA 0.100 inch Contact Spacing 4 Brown STROBE Mates to Molex 22-05-2051 Note: Vcc = 2.7 to 5.5 VDC 5 Green CARD PRESENT Connector for Single Track, 5 Pin Table 2-2.
Section 2. Installation Table 2-3. I/O Connector for 3-Track, 9 Pin Pin Number 1 Color Red 2 Blue 3 Brown DATA (Tk 1) 4 Green STROBE (Tk 2) 5 Yellow DATA (Tk 2) Molex 9 Pin 6 Gray 51004-0900 7 Orange 2.0 mm Contact Spacing 8 White CARD PRESENT Mates to Molex 53014-0910 Note: Vcc = 2.7 to 5.
90-millimeter Compatible Swipe Reader DATA The Data signal is valid while the strobe is low. If the Data signal is high, the bit is a zero. If the Data signal is low, the bit is a one. STROBE The Strobe signal indicates when Data is valid. It is recommended that Data be loaded by the user with the leading edge (negative) of the Strobe. CARD PRESENT Card Present will go low after 14/15 flux reversals from the head. Card Present will return high 150 milliseconds after the last flux reversal.
