Instructions / Assembly

ManualsBrandsMagTorch ManualsSoldering3-in-1 Micro Flame Pro Butane Soldering Torch

ENGLISH:

OPERATING INSTRUCTIONS

WARNING:

Accessible parts may be very hot. Keep young children away from the appliance. Use only in

well-ventilated area. Do not use the

appliance if it has damaged or worn seals. Dot not use the appli-ance if it is leaking, damaged,

or is not operating properly. Do not

modify this appliance. IMPORTANT: Read the instructions carefully before using the appliance.

Keep this booklet and read it when necessary.

IGNITION: 1.Make sure the exhaust vent is facing upward to avoid the damage of tabletop.

2.Press the safety lock button and simultaneously using your thumb to pull down the trigger.

This action will ignite the soldering iron. 3.Hold the ignition button and release the safety lock

button. Move the continuous flame switch to right for a constant flame. 4.Press the Flame Off

button for about 1 second to turn off the flame, gas flowing though the internal catalyst after

ignition will generate heat. If you don’t press the Flame Off button, the temperature of

soldering iron will be too high. EXTINGUISHING: Move the Continuous Flame Switch to left, and

this will cut off the gas supply and extinguish the flame. HEAT GUN: Disassemble the soldering

tip by rotating the tip counterclockwise. The assembly will now be used as hot blower without

the soldering tip. Operation will be the same as above for the soldering iron. TORCH:

Disassemble the soldering assembly by rotating the assembly lock counterclockwise. Take off

the soldering device and install the metal sleeve back to the unit. Operation will be the same as

above for the soldering iron. FLAME ADJUSTMENT: Move the adjustment lever toward right

side to increase the flame strength or toward left to decrease the flame strength. When the

flame is at “+” position, the longer flames may cause the torch to flare or extinguish. In this

situation, please move the gas adjustment lever to “-” side for decreasing the flame strength

and set up a most efficient flame. REFILLING TORCH WITH FUEL: 1.Turn off the soldering iron

and make sure the flame is off. 2.Wait until the soldering iron temperature has cooled down

naturally before refilling gas. 3.Hold the soldering iron in an upside down position. 4.Insert and

press down the butane canister nozzle into the soldering iron refilling valve. Use short 3-5

second bursts with the fuel cylinder. 5.Stop refilling once gas starts to overflow. The soldering

iron should never be completely filled. OVERFILLING WILL CAUSE THE FLAME TO SPIT. 6.Please

allow a few minutes for gas to stabilize before operation.

GENERAL SAFETY RULES:

Read and follow operating instructions and warning and familiarize yourself with the torch

before lighting or using. Review instructions and warnings periodically to maintain awareness. •

Keep the burner out of the reach of children. • Extremely flammable contents under pressure. •

Maintain good ventilation. • Always wear goggles and protective gloves and use proper tools to

handle hot work. • Never breathe in welding/soldering fumes. • Do not puncture or incinerate.

• Never attempt to modify the torch construction, use unapproved accessories or fuels, or

attempt to repair a damaged torch. • Do not drop the micro torch as the unit might be

Summary of content (5 pages)

PAGE 1
ENGLISH: OPERATING INSTRUCTIONS WARNING: Accessible parts may be very hot. Keep young children away from the appliance. Use only in well-ventilated area. Do not use the appliance if it has damaged or worn seals. Dot not use the appli-ance if it is leaking, damaged, or is not operating properly. Do not modify this appliance. IMPORTANT: Read the instructions carefully before using the appliance. Keep this booklet and read it when necessary. IGNITION: 1.
PAGE 2
damaged and ceramic could be broken • Never store at temperature above 45°C (133°F) such as in a car or prolonged sunlight. • Follow refilling procedure to avoid serious accidents. • Do not ignite the torch near to the face, hands, clothing or inflammable materials. • Please note the butane flame may be barely visible in certain light conditions. • Allow the micro torch to cool down before storage. • Ensure flame is extinguished and gas is off after each use.
PAGE 3
de la flamme ou vers la gauche pour diminuer la force de la flamme. Lorsque la flamme est sur la position « + » les flammes plus longues peuvent faire en sorte que la torche flamboie ou s’éteigne. Dans ce cas, veuillez déplacer le levier de réglage du gaz du côté « - » pour diminuer l’intensité de la flamme et obtenir une flamme plus efficace. REMPLISSAGE DE LA TORCHE AVEC DU CARBURANT: • Éteindre le fer à souder et s’assurer que la flamme est éteinte.
PAGE 4
SPANISH: INSTRUCCIONES DE OPERACIÓN ADVERTENCIA: Las piezas accesibles podrían estar muy calientes. Mantenga los niños alejados del aparato. Sólo utilice en lugares bien ventilados. No utilice el aparato si éste tiene sellos dañados o desgastados. No utilice el aparato si éste tiene fuga, está dañado, o no está funcionando apropiadamente. No modifique este aparato. IMPORTANTE: Lea cuidadosamente las instrucciones antes de utilizar el aparato. Guarde este folleto y léalo cuando sea necesario. ENCENDIDO: 1.
PAGE 5
Siempre utilice gafas de seguridad y guantes protectores, y utilice herramientas apropiadas para manipular la pieza caliente. • Nunca inhale los humos de la soldadura eléctrica / soldadura con soplete. • No perfore ni incinere. • Nunca intente modificar la construcción del soplete, nunca utilice combustibles o accesorios no aprobados, ni nunca intente reparar un soplete dañado.