User`s manual

ii
The contents of this manual are subject to change without prior notice. Should revisions be necessary, updates to all
Magtrol User’s Manuals can be found at Magtrol’s web site at www.magtrol.com/support/manuals.htm.
Please compare the date of this manual with the revision date on the web site, then refer to the manual’s Table of
Revisions for any changes/updates that have been made since this edition.
REVISION DATE
1st Edition, revision J – March 2010
TABLE OF REVISIONS
Revisions To This Manual
Date Edition Change Section(s)
03/01/10 1st Edition - rev. J Added 60 bit encoder to chart for torque transducers 3.3.1
04/16/09 1st Edition - rev. I Added UE commands 5 = 1-bit, 6 = 2-bit and 7 = 6-bit. 8.6.4
05/18/05 1st Edition - rev. H Changed M-TEST 4.0 references to “M-TEST” or “M-TEST 5.0” throughout
manual
06/28/04 1st Edition - rev. G Removed DSP6001 resetting procedure 9.4
05/24/04 1st Edition - rev. F Added DIR#, OH1 and IOXX.XX Misc. Command codes 8.6.7, D.6
08/05/03 1st Edition - rev. E Ratings changes for: Operating Temperature, Accuracy,
Temperature Coefficient and Accessory Torque/Speed Output
1.3
08/05/03 1st Edition - rev. E Auxiliary Input rating replaced with Input Voltage Range 1.3
08/05/03 1st Edition - rev. E Screen Saver function removed 2.3.2
08/05/03 1st Edition - rev. E Added Power Alarm to priority table 6.1.3
08/05/03 1st Edition - rev. E Deleted DDLXX.XX Ramp Command code 8.6.3, D.3
08/05/03 1st Edition - rev. E Deleted A,B,C,D and E Speed Command codes 8.6.3, 8.6.5, D.3
08/05/03 1st Edition - rev. E Deleted C# Misc. Command code 8.6.7, D.6
05/06/02 1st Edition - rev. D Speed check and decimal point check added to calibration
procedure
9.3.5 & 9.3.6
12/20/01 1st Edition - rev. C Added values for analog filter setup (AF1# and AF2#) 8.6.4
12/20/01 1st Edition - rev. C Added filter cutoff frequency 4.1
08/27/01 1st Edition - rev. B Changed name of chapter titles Chap. 7 & 8
08/27/01 1st Edition - rev. B Changed name and location of Additional Scale Factor Table Appendix F
08/27/01 1st Edition - rev. B Updated Power Analyzers in System Options table 1.3
07/23/01 1st Edition - rev. A Updated Motor Testing Software section and System Options 1.3
07/23/01 1st Edition - rev. A Increased range of PID numbers when using the multiplier 5.4
07/23/01 1st Edition - rev. A Changed Contact Configuration and Manufacturer P/N under
Relay Specifications
6.1.1
07/23/01 1st Edition - rev. A Air Flow Alarm for Eddy-Current/Powder Brake Dynamometers
is not available
6.1.3
07/23/01 1st Edition - rev. A Changed IDN? command to *IDN? command 8.6
07/23/01 1st Edition - rev. A Added alarm condition to explanation of OD command 8.6
07/23/01 1st Edition - rev. A Entered exact figures for reference voltage 9.3.2, 9.3.3
07/23/01 1st Edition - rev. A Defined accepted voltage range in steps 3, 6, 9 & 14 9.3.4
03/27/01 1st Edition Complete re-write of Preliminary Manual entire manual