Installation Guide

ManualsBrandsMain Door ManualsBuilding materialsRustic Collection 2-1/4 in. x 80 in. Prefinished Solid Mahogany Type Brickmold Kit

How to Install Door Casing/Brick Molding

Door casing(interior) and Brick molding(exterior), is the wood trim applied to a doorjamb. It creates a finished frame for the

doorjamb and conceals the perimeter shim space used to secure the doorjam b to the adjacent wall framing on both the exterior and

interior of the door. This will create the finished look for your door unit.

Things You'll Need

Tape measure

Finish hammer

Miter saw

6d finish nails

8d finish nails

Nail set

Stainable Filler/Finish

Instructions

1. Use a tape measure and pencil to mark the edge of the doorjamb, ¼ inch from the door opening. Make the first mark at the

bottom of the jamb on the strike side, opposite the hinge side, and repeat at approximately 12 -inch increments around the

perimeter of the jamb. These marks will define the casing setback, called the reveal, and guide the attachment of each casing pi ece.

2. Measure the distance from the bottom of the jamb on the strike side to the bottom of the horizontal headpiece at the top o f the

jamb. Mark this measurement plus ¼ inch on a length of door casing, ensuring the end from which you measure is cut square and

you mark what will be the inside edge of the casing piece.

3. Set your miter saw to a 45-degree angle and cut the casing piece marked in Step 2, so that the measured mark is the short point

of the miter cut.

4. Position the piece of casing cut in Step 3 against the edge of the doorjamb and align it with the ¼ -inch reveal marked in Step 1.

Be sure the short point of the miter cut at the top extends ¼ inch beyond the bottom edge of the top jamb. Attach the casing at each

mark with a 6d finish nail.

5. Open the door and measure the horizontal dimension between the inside faces of the doorjamb at the top.

6. Mark a piece of casing molding with the measurement determined in Step 5 plus ½ inch. Position the marks on the casing piece to

allow them to be the short points of opposing 45-degree angles at each end of the piece. Cut both angles with the miter saw.

7. Position the casing piece cut in Step 6 at the edge of the head jamb and align it with the ¼ -inch reveal marked in Step 1. Attach

the head piece at each reveal mark with a 6d finish nail.

8. Repeat Steps 2, 3 and 4 for the remaining jamb piece on the hinge side of the doorjamb.

9. Nail the outer edge of the casing pieces into the adjacent wall with 8d finish nails spaced 12 to 16 inches apart around the

perimeter to hold the casing edge tight against the wall surface.

10. Repeat Steps 1 through 9 for the casing molding on the opposite side of the doorjamb. Use a nail set to set all of the nail h eads

1/16 inch below the casing surface. Fill and Finish the nail holes.

Main Door does not accept any responsibility nor does it offer any warranty for the information provided herein. These instructions are provided as a general guideline. Please seek

additional information if you have questions or seek the advice of a licensed professional carpenter.

Summary of content (1 pages)

PAGE 1
How to Install Door Casing/Brick Molding Door casing(interior) and Brick molding(exterior), is the wood trim applied to a doorjamb. It creates a finished frame for the doorjamb and conceals the perimeter shim space used to secure the doorjamb to the adjacent wall framing on both the exterior and interior of the door. This will create the finished look for your door unit. Things You'll Need Tape measure Finish hammer Miter saw 6d finish nails 8d finish nails Nail set Stainable Filler/Finish Instructions 1.