CONTACT US FIRST sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-523-3987. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) You won't just fall in love with it. You'll fall asleep in it. Storage Bed/Headboard Model 413852 Share your journey! NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-30 Hammer Français 31-34 Español 35-38 Warranty Not actual size Skip the power trip. This time. 39 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know our ABCs. Part Identification J A2 B D R A2 X D L M B2 A J2 N E J2 I2 J2 C2 B2 G2 J2 D44 F H2 D476 D453 B19 D44 D45 M67 T D476 D453 B19 D45 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push thirty-four HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C2 and D), PANELS (G2, H2, and I2), SHELF (L), and BRACES (M, N, and M67). Then, insert a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å IMPORTANT: The Headboard can be attached to either end of the Storage Bed. In the following steps, assemble your unit according to what option you choose. Headboard on the RIGHT Headboard on the LEFT Page 6 413852 www.sauder.
Step 3 å Fasten a CABINET RIGHT (35GA) and CABINET LEFT (35GB) to the HEADBOARD (E) and FOOTBOARD (F). Use four GOLD 5/16" FLAT HEAD SCREWS (3S). 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Headboard on the RIGHT Roller end Rounded edge Fi ni sh ed su rfa ce E Roller end F Roller end Headboard on the LEFT Rounded edge su rfa ce F Fi ni sh ed Roller end E www.sauder.
Step 4 å Fasten a CABINET RIGHT (35GA) and CABINET LEFT (35GB) to the LOWER UPRIGHT (C2). Use four GOLD 5/16" FLAT HEAD SCREWS (3S). 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end These HIDDEN CAMS are closer to this edge. S HI urfa DD ce EN wi CA th M S C2 Page 8 Roller end 413852 www.sauder.
Step 5 å Fasten the UPRIGHTS (D) to the TOP (J). Tighten two HIDDEN CAMS. å Fasten the SHELF (L) to the UPRIGHTS (D). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) L th S wi AM ce C rfa EN Su IDD H Angled edge D D Angled edge J Surface with HIDDEN CAM Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 6 å Fasten four ANGLE BRACKETS (5G) to the SHELF BRACE (M). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the SHELF BRACE. å Fasten the SHELF BRACE (M) to the SHELF (L). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). M ce rfa Su th wi EN DD HI S M CA 1S 5G BLACK 9/16" LARGE HEAD SCREW (8 used in this step) M Sur fac ew ith HID DEN CA MS L These surfaces should be even. Angled edge Page 10 413852 www.sauder.
Step 7 å Fasten the ENDS (A and B) to the TOP (J), SHELF (L), and SHELF BRACE (M). Tighten twelve HIDDEN CAMS. å Fasten two METAL BRACKETS (4G) to the ENDS (A and B). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the BRACKETS are even with the edges of the ENDS (A and B).
Step 8 å å å å Carefully lay your unit onto its front edges. Maximum 210 degrees Insert two METAL PINS (1R) into the LOWER BRACE (N). Fasten the LOWER BRACE (N) to the ENDS (A and B). Tighten two HIDDEN CAMS. Arrow Minimum 190 degrees NOTE: Be sure the METAL PINS in the LOWER BRACE insert into the holes in the ENDS. A ce rfa Su th wi EN DD HI B S M CA N 1R Page 12 413852 www.sauder.
Step 9 å å Lay the BACK (X) over your unit. å å Fasten the BACK (X) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. å Caution Make equal margins along all four edges of the BACK (X). Push on opposite corners of your unit if needed to make it "square". Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHTS (D).
Step 10 å Using your hammer, tap ten TACK GLIDES (12E) into the edges of the LOWER UPRIGHT (C2), HEADBOARD (E), FOOTBOARD (F), LOWER FRONT PANEL (H2), and BACK PANEL (I2). 12E H2 Unfinished edge I2 Unfinished edge Unfinished edge C2 Unfinished edge F Unfinished edge 12E Page 14 E 413852 www.sauder.
Step 11 å Fasten the SLATS (J2) to the UPPER FRONT PANEL (G2) and BACK PANEL (I2). Use twelve SILVER 1-1/8" FLAT HEAD SCREWS (10S). å Fasten the BOTTOM SUPPORTS (B2) to the HEADBOARD (E) and FOOTBOARD (F). Use eight SILVER 1-1/8" FLAT HEAD SCREWS (10S). å Insert a METAL PIN (1R) into each HEADBOARD (E) and FOOTBOARD (F). 10S Edge without holes SILVER 1-1/8" FLAT HEAD SCREW (20 used in this step) J2 J2 G2 J2 I2 J2 Edge without holes 1R Edge without holes B2 F B2 E Rounded edge 1R www.sauder.
Step 12 å å Carefully stand your unit upright. Fasten the HEADBOARD (E) to the LOWER BRACE (N). Use three SILVER 1-1/8" FLAT HEAD SCREWS (10S). 10S å Fasten the HEADBOARD (E) to the METAL BRACKETS on the ENDS (A and B). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å å NOTE: Follow steps 13-16 for Headboard on the Right.
Step 13 å Fasten the BACK PANEL (I2) to the HEADBOARD (E). Tighten three HIDDEN CAMS. å Fasten the LOWER UPRIGHT (C2) to the BACK PANEL (I2). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Headboard on the RIGHT Finished edge E I2 These HIDDEN CAMS are closer to the long edge. fi Un ce rfa u s ed h nis C2 Roller end www.sauder.
Step 14 å Fasten the LOWER FRONT PANEL (H2) to the HEADBOARD (E) and LOWER UPRIGHT (C2). Tighten two HIDDEN CAMS. å NOTE: Be sure the METAL PIN in HEADBOARD inserts into the hole in the LOWER FRONT PANEL. å Fasten the UPPER FRONT PANEL (G2) to the HEADBOARD (E) and LOWER UPRIGHT (C2). Tighten three HIDDEN CAMS.
Step 15 å å Fasten the FOOTBOARD (F) to the FRONT PANELS (G2 and H2) and BACK PANEL (I2). Tighten six HIDDEN CAMS. Maximum 210 degrees NOTE: Be sure the METAL PIN in the FOOTBOARD inserts into the hole in the LOWER FRONT PANEL. Arrow Minimum 190 degrees Headboard on the RIGHT Rounded edge I2 G2 F Sur fac ew itho ut h ole s www.sauder.
Step 16 å Fasten the BRACKETS (1G) to the BOTTOM SUPPORTS (B2), LOWER UPRIGHT (C2), and PANELS (G2, H2, and I2). Use twelve BLACK 9/16" LARGE HEAD SCREWS (1S). Headboard on the RIGHT 1S BLACK 9/16" LARGE HEAD SCREW (12 used in this step) 1G 1G B2 1G I2 C2 G2 1G H2 1G B2 1G Page 20 413852 www.sauder.
Step 17 å Fasten the BACK PANEL (I2) to the HEADBOARD (E). Tighten three HIDDEN CAMS. å Fasten the LOWER UPRIGHT (C2) to the BACK PANEL (I2). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Headboard on the LEFT Finished edge E I2 out h t i ew fac r u S S AM C DEN HID C2 Un fin ish ed su rfa ce Roller end www.sauder.
Step 18 å Fasten the LOWER FRONT PANEL (H2) to the HEADBOARD (E) and LOWER UPRIGHT (C2). Tighten two HIDDEN CAMS. å NOTE: Be sure the METAL PIN in HEADBOARD inserts into the hole in the LOWER FRONT PANEL. å Fasten the UPPER FRONT PANEL (G2) to the HEADBOARD (E) and LOWER UPRIGHT (C2). Tighten three HIDDEN CAMS.
Step 19 å Fasten the FOOTBOARD (F) to the FRONT PANELS (G2 and H2) and BACK PANEL (I2). Tighten six HIDDEN CAMS. å NOTE: Be sure the METAL PIN in the FOOTBOARD inserts into the hole in the LOWER FRONT PANEL. Maximum 210 degrees Arrow Minimum 190 degrees Headboard on the LEFT Rounded edge I2 G2 H2 F e fac r u S www.sauder.
Step 20 å Fasten the BRACKETS (1G) to the BOTTOM SUPPORTS (B2), LOWER UPRIGHT (C2), and PANELS (G2, H2, and I2). Use twelve BLACK 9/16" LARGE HEAD SCREWS (1S). Headboard on the LEFT 1S 1G BLACK 9/16" LARGE HEAD SCREW (12 used in this step) 1G 1G B2 C2 I2 1G B2 G2 1G H2 1G Page 24 413852 www.sauder.
Step 21 å Fasten the BOTTOMS (A2) to the BOTTOM SUPPORTS (B2), LOWER UPRIGHT (C2), and SLATS (J2). Use ten BROWN 1-5/8" FLAT HEAD SCREWS (55S). 55S BROWN 1-5/8" FLAT HEAD SCREW (10 used in this step) A2 B2 J2 A2 C2 J2 B2 J2 J2 www.sauder.
Step 22 å Using your hammer, gently tap twelve SUPPORT PINS (4R) into the center holes in the DRAWER FRONTS (S and T) and DRAWER BACKS (D476). T S D476 D476 4R Page 26 413852 (12 used) www.sauder.
Step 23 å Pull the DRAWER FRONT BRACKETS (8G) apart and slide them into the grooves in the DRAWER SIDES (D44 and D45). You may need to gently tap them in with a hammer. å å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification. å NOTE: The RIGHT DRAWER FRONT has a locator hole. This DRAWER FRONT will always be positioned on the right side of the Storage Bed. å Slide the DRAWER BOTTOM (B19) into the grooves in the DRAWER SIDES (D44 and D45) and RIGHT DRAWER FRONT (T).
Step 24 å Fasten the DRAWER BRACE (M67) to the RIGHT DRAWER FRONT (T). Tighten one HIDDEN CAM. å Fasten the DRAWER BACK (D476) to the DRAWER SIDES (D44 and D45) and DRAWER BRACE (M67). Use five BLACK 1-9/16" FLAT HEAD SCREWS (30S). å Maximum 210 degrees Arrow Minimum 190 degrees Repeat this step for the other drawer. Hidden part using recycled material. Color may vary. M67 T Start each screw a few turns before completely tightening any of them.
Step 25 å Fasten a DRAWER RIGHT (35GC) and DRAWER LEFT (35GD) to the DRAWER SIDES (D44 and D45). Use four GOLD 5/16" FLAT HEAD SCREWS (3S). å Slide a DRAWER DIVIDER (D453) into the SUPPORT PINS on the RIGHT DRAWER FRONT (T) and DRAWER BACK (D476). å Repeat this step for the other drawer. Roller end Finished edge D45 D453 D476 T Roller end D44 (4 screws per drawer) 3S GOLD 5/16" FLAT HEAD SCREW (8 used in this step) www.sauder.
Step 26 å To insert the drawers into your unit, tip the front of the drawer down slightly and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. å To make adjustments to the drawer, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. å Push the RUBBER SLEEVES (2R) over the remaining METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the UPRIGHTS (D).
Modèle 413852 Lit avec rangement / Tête de lit Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer quatre CONSOLES À ÉQUERRE (5G) à l'ENTRETOISE DE TABLETTE (M). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (1S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. REMARQUE : S'assurer que les chants des CONSOLES À ÉQUERRE sont à fleur du chant de l’ENTRETOISE DE TABLETTE.
ÉTAPE 10 ÉTAPE 15 À l'aide d'un marteau, enfoncer dix PATINS (12E) dans les chants du MONTANT INFÉRIEUR (C2), de la TÊTE DE LIT (E), du PIED DE LIT (F), PANNEAU AVANT INFÉRIEUR (H2) et du PANNEAU ARRIÈRE (I). Fixer le PIED DE LIT (F) aux PANNEAUX AVANT (G2 et H2) et au PANNEAU ARRIÈRE (I2). Serrer six EXCENTRIQUES ESCAMOTABLES. REMARQUE : S’assurer de bien insérer la GOUPILLE EN MÉTAL du PIED DE LIT dans le trou du PANNEAU AVANT INFÉRIEUR.
ÉTAPE 20 ÉTAPE 24 Fixer les CONSOLES (1G) aux SUPPORTS INFÉRIEURS (B2), MONTANT INFÉRIEUR (C2) et aux PANNEAUX (G2, H2 et I2). Utiliser douze VIS TÊTE LARGE 14 mm NOIRES (1S). Fixer l’ENTRETOISE DE TIROIR (M67) au DEVANT DE TIROIR DROIT (T). Serrer un EXCENTRIQUE ESCAMOTABLE. ÉTAPE 21 Fixer l'ARRIÈRE DE TIROIR (D476) aux CÔTÉS DE TIROIR (D44 et D45) et à l’ENTRETOISE DE TIROIR (M67). Utiliser cinq VIS TÊTE PLATE 40 mm NOIRES (30S). Répéter cette étape pour l'autre tiroir.
Cama / Cabecera de Cama con capacidad de almacenaje Modelo 413852 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 8 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Cuidadosamente coloque la unidad para que repose sobre los bordes delanteros. Inserte dos ESPIGAS DE METAL (1R) dentro de la RIOSTRA INFERIOR (N). Empuje treinta y cuatro EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), los PARALES (C2 y D), los PANELES (G2, H2 e I2), el ESTANTE (L) y las RIOSTRAS (M, N y M67).
PASO 13 Fije el PANEL POSTERIOR (I2) a la CABECERA DE CAMA (E). Apriete tres EXCÉNTRICOS ESCONDIDOS. Fije el PARAL INFERIOR (C2) al PANEL POSTERIOR (I2). Apriete dos EXCÉNTRICOS ESCONDIDOS. PASO 18 Fije el PANEL INFERIOR FRONTAL (H2) a la CABECERA DE CAMA (E) y al PARAL INFERIOR (C2). Apriete dos EXCÉNTRICOS ESCONDIDOS. NOTA : Asegúrese que la ESPIGA DE METAL en el PANEL INFERIOR FRONTAL se introduzca en el agujero en la CABECERA DE CAMA.
PASO 21 Fije los FONDOS (A2) a los SOPORTES DE FONDO (B2), al PARAL INFERIOR (C2) y a los LISTONES DE REJILLA (J2). Utilice diez TORNILLOS MARRONES DE CABEZA PERDIDA de 41 mm (55S). PASO 22 PASO 24 Fije la RIOSTRA DE CAJÓN (M67) a la CARA DERECHA DE CAJÓN (T). Apriete un EXCÉNTRICO ESCONDIDO. Fije el DORSO DE CAJÓN (D476) a los LADOS DE CAJÓN (D44 y D45) y a la RIOSTRA DE CAJÓN (M67). Utilice cinco TORNILLOS NEGROS DE CABEZA PERDIDA de 40 mm (30S).
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-523-3987 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
