LOT NUMBER: DATE OF PURCHASE: / / End Table Stock # MS98-020-082-01 # MS98-020-082-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: End Table MODEL # MS98-020-082-01/-02 MADE IN CHINA MAXIMUM LOAD 50 lb. (22.7 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. SPECIAL NOTE Please read the instruction sheets completely before assembly. Examine all packaging material before discarding carton.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Table Top (Qty. 1) B- Side Frame (Qty. 2) C- Top Stretcher (Qty. 2) D- Bottom Stretcher (Qty. 2) (1) 1/4" x 5/8” Bolt (Qty. 8+1 extra) (2) Lock Washer (Qty. 8+1 extra) (3) Flat Washer (Qty. 8+1 extra) (4) M4 x 32 mm Screw (Qty. 8+1 extra) (5) Floor Leveler (Qty. 4) Hex Wrench (Qty.
Assembly Instructions B D D B C 1 2 3 C D D B B C 3 2 1 C 1/4" x 5/8” Bolt (8 used in this step) Lock Washer (8 used in this step) ① ② Flat Washer (8 used in this step) ③ 1. Unpack the units and confirm that you have all hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Attach the Stretchers (C and D) between the Side Frames (B) with eight 5/8” Bolts (1) and eight Washers (2 and 3) as shown.
Assembly Instructions B B 4 C C A M4 x 32 mm Screw (8 used in this step) ④ 3. Attach the previous assembly to the Table Top (A) with eight 32 mm Screws (4).
Assembly Instructions 5 B B Floor Leveler (4 used in this step) ⑤ 4. Screw four Floor Levelers (5) into the threaded sockets on the Side Frames (B).
Assembly Instructions A B B 5. Stand the assembled unit upright. 6. In case of uneven floors, adjust the installed Floor Levelers (5) at the bottom of the Side Frames (B) to level the unit.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
NÚMERO DEL LOTE: FECHA DE COMPRA / / Mesa lateral Serie # MS98-020-082-01 # MS98-020-082-02 ENSAMBLE REQUERIDO POR ADULTOS Si tiene alguna pregunta relacionada con el montaje o si faltan piezas, NO devuelva este producto al establecimiento donde lo adquirió.
MÁXIMO PESO RECOMENDADO FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Mesa lateral MODELO # MS98-020-082-01/-02 HECHO EN CHINA CARGA MÁXIMA 50 lb. (22.7 kg) ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRÍA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. NOTA ESPECIAL Lea atentamente toda la hoja de instrucciones antes de comenzar el montaje. Antes de deshacerse del empaque compruebe que no ha olvidado nada en su interior.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y material de ferretería indicadas se encuentran presentes antes del comienzo del montaje. A- Superficie de mesa (Cant. 1) B- Marco lateral (Cant. 2) C- Bastidor superior (Cant. 2) D- Bastidor inferior (Cant. 2) (1) Pernos de 1/4" x 5/8” (Cant. 8+1 extra) (2) Arandela de sujeción (Cant. 8+1 extra) (3) Arandela plana (Cant. 8+1 extra) (4) Tornillo M4 x 32 mm (Cant.
Instrucciones de ensamblaje B D D B C 1 2 3 C D D B B C 3 2 1 C Perno de 1/4" x 5/8” (8 usados en este paso) Arandela de sujeción (8 usadas en este paso) ② ① Arandela plana (8 usadas en este paso) ③ 1. Desempaquete las unidades y confirme que tiene todas las piezas y herramientas necesarias. Ensamble la unidad en un suelo alfombrado o en la caja de cartón vacía para evitar rayaduras. 2.
Instrucciones de ensamblaje B B 4 C C A Tornillo M4 x 32 mm (8 usados en este paso) ④ 3. Conecte el montaje anterior a la superficie de mesa (A) con ocho tornillos de 32 mm (4).
Instrucciones de ensamblaje 5 B B Nivelador de piso (4 usados en este paso) ⑤ 4. Atornille cuatro niveladores de piso (5) en los insertos roscados en los marcos laterales (B).
Instrucciones de ensamblaje A B B 5. Coloque la unidad ensamblada en posición vertical. 6. En caso de suelos irregulares, ajuste los niveladores de piso ya instalados (5) en la parte inferior de los marcos laterales (B) para nivelar la unidad.
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayones. El uso de cera para pulir muebles no es necesario. Si desea usar cera pruebe en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que puede dañar el acabado. Siempre utilice protección para vasos cuando los coloque sobre la unidad.