User Instructions

Open
Close
Off
Play Try me
Step 1
Step 2
User Guideline for Paring the Bluetooth function
First time set up:
1) Turn off all Bluetooth devices nearby. i.e. speakers, phone, hands-free
control devices etc.
2) Press Bluetooth button on scooter. (D)
When the blue light is flashing it is ready to be paired (linked) to a device.
3) Turn on your phone’s Bluetooth.
4) Search for “OG Ride Along Scooter™” from your smart phone and select.
Phone will be paired (linked) to the scooter and ready to play sound.
For trouble connecting to the Bluetooth scooter, please read the following carefully.
• Turn off all nearby Bluetooth devices nearby. i.e., speakers, phone,
hands-free control devices etc. and repeat steps 1-4 above.
• If blue light is dimmed, it is time to replace the batteries.
• If abnormal sounds are produced, switch the scooter to the “OFF” position
for 2 seconds and then switch back to “Play”.
• To clean, use a soft damp cloth to remove dust from scooter.
• Do not use abrasive cloths or strong cleaning detergent as this will cause
permanent surface damage to the scooter.
• Please read this instruction sheet carefully and keep it for future reference.
The product contains the Bluetooth play function, which can
link to any smart device with Bluetooth V2.1 and above.
QDID number: 61231
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada
regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successfulcommunication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs,
il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonn ée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autoris é e aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit
different from that to whichthe receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference thatmay cause undesired operation. Shielded cables must be used with this unit to
ensure compliance with the ClassB FCC limits. FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons. The device must not be co-located or operating in conjunction with any other antenna or transmitter. “This
device complies with FCC radiation exposure limits set forth for general population (uncontrolled exposure).
This device must not be collocated or operating in conjunction with any other antenna or transmitter.”
CAUTION:
Uses 3 x AA (1.5V) size batteries – Included
Do not mix old and new batteries.
Do not mix alkaline, standard
(carbon-zinc), or rechargeable
(nickel-cadmium) batteries.
Do not dispose of this product in fire.
Batteries inside product may explode
or leak.
Batteries Replacement
To replace batteries: Unscrew the battery cover
and replace 3 x AA (1.5V) size batteries.
Product is shipped in the “Try me” mode.
Slide the switch to “Play” position.
Print 1 solid color PMS 676 C
Size A4: 11.69” x 8.27”