Instruction manual cordless lawn trimmer
14 ENGLISH
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION: Never start the tool unless it is
completely assembled.2SHUDWLRQRIWKHWRROLQD
partially assembled state may result in serious per-
VRQDOLQMXU\IURPDFFLGHQWDOVWDUWXS
Installing the front grip
$WWDFKWKHIURQWJULSWRWKHIURQWJULSKROGHUDQGVHFXUH
it with a hex bolt and the thumb nut as shown in the
¿JXUH
ŹFig.15: 1. Front grip 2.7KXPEQXW3. Hex bolt
7KHIURQWJULSDQJOHLVDGMXVWDEOH7RDGMXVWWKHIURQW
JULSDQJOHORRVHQWKHWKXPEQXWVHWWKHIURQWJULSDWDQ
proper angle according to your work and then tighten
WKHWKXPEQXWFORFNZLVH¿UPO\
Installing the wire guard
NOTICE: Do not expand the wire guard outward
too much. Otherwise it may break.
ŹFig.16
7RUHGXFHWKHULVNRIGDPDJLQJWKHREMHFWVLQIURQWRIWKH
cutting head, attach the wire guard to the protector so
that it controls the cutting range.
Slightly expand the wire guard outward and then insert
LWLQWRWKHKROHVRIWKHSURWHFWRU
For nylon cutting head:
$WWDFKWKHZLUHJXDUGWRWKHKROHVRQWKHIURQWVLGHRI
WKHSURWHFWRU7KHQ\ORQFRUGPDUNRQWKHSURWHFWRU
indicates the hole to be used.
ŹFig.17: 1. Hole
For plastic blade head:
$WWDFKWKHZLUHJXDUGWRWKHKROHVRQWKHUHDUVLGHRIWKH
SURWHFWRU7KHEODGHPDUNRQWKHSURWHFWRULQGLFDWHVWKH
hole to be used.
ŹFig.18: 1. Hole
:KHQZLUHJXDUGLVQRWLQXVHOLIWLWIRUWKHLGOHSRVLWLRQ
ŹFig.19: 1. Wire guard
Installing the protector
CAUTION: While installing the protector, be
careful not to contact the nylon cord cutter on
the protector. Contact with the cutter could result in
SHUVRQDOLQMXU\
ŹFig.20: 1. Screw 2. Protector
0RXQWWKHSURWHFWRUE\¿WWLQJLWRQWRWKHPRWRUKRXVLQJ
and then secure it with two screws.
Installing nylon cutting head
Optional accessory
CAUTION: If the nylon cutting head acciden-
tally impacts a rock or hard object during oper-
ation, stop the tool and inspect for any damage.
If the nylon cutting head is damaged, replace it
immediately.8VHRIDGDPDJHGFXWWLQJWRROFRXOG
UHVXOWLQVHULRXVSHUVRQDOLQMXU\
CAUTION: Be sure to remove the hex wrench
after installation.
CAUTION: When installing or removing the
nylon cutting head, be careful not to contact the
nylon cord cutter on the protector. Contact with the
FXWWHUPD\UHVXOWLQSHUVRQDOLQMXU\
NOTICE: Be sure to use genuine Makita nylon
cutting head.
1. 7XUQWKHWRROXSVLGHGRZQVRWKDW\RXFDQUHSODFH
the cutting tool easily.
2. Insert the hex wrench through the hole on the
motor housing and rotate the spindle until the spindle is
locked.
ŹFig.21: 1. Hex wrench 2. Hole 3. Spindle
3. Place the nylon cutting head onto the spindle and
tighten it by turning it clockwise.
ŹFig.22: 1. Nylon cutting head
4. Remove the hex wrench.
7RUHPRYHWKHQ\ORQFXWWLQJKHDGWXUQLWFRXQWHUFORFN-
wise while locking the spindle with the hex wrench.
Installing plastic blade head
Optional accessory
CAUTION: If the plastic blade accidentally
impacts a rock or hard object during operation,
stop the tool and inspect for any damage. If the
plastic blade is damaged, replace it immediately.
8VHRIDGDPDJHGFXWWLQJWRROFRXOGUHVXOWLQVHULRXV
SHUVRQDOLQMXU\
CAUTION: Be sure to remove the hex wrench
after installation.
CAUTION: When installing or removing the
plastic blade head, be careful not to contact the
nylon cord cutter on the protector. Contact with the
FXWWHUPD\UHVXOWLQSHUVRQDOLQMXU\
CAUTION: If the plastic blade head is worn
out, replace it with a new one.,ILWLVZRUQRXWWKH
SODVWLFEODGHPD\EHWKURZQDZD\IURPWKHSODVWLF
EODGHKHDGGXULQJRSHUDWLRQDQGFDXVHDQLQMXU\
NOTICE: Be sure to use genuine Makita plastic
blade.
1. 7XUQWKHWRROXSVLGHGRZQVRWKDW\RXFDQUHSODFH
the cutting tool easily.
2. Insert the hex wrench through the hole on the
motor housing and rotate the spindle until the spindle is
locked.