923H (12lang)(cover) (’100. 6.
1923H (illust) (12lang)(’100. 6.
1923H (illust) (12lang)(’100. 6. 30) 23 24 21 22 9 10 0.3 mm – 0.
1923H (illust) (12lang)(’100. 6.
1923H (illust) (12lang)(’100. 6.
1923H (E) (’100. 7. 6) ENGLISH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Bolt Drum Planer blade Drum cover Adjust plate Blade edge Screws Heel Back side of gauge base Inside edge of gauge plate Gauge plate Gauge base Pan head screw Planer blade locating lugs Heel of adjust plate Set plate Inside flank of gauge plate Mini planer blade Explanation of general view 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Hex.
1923H (E) (’100. 6. 30) OPERATING INSTRUCTIONS Removing or installing planer blades Important: • Always be sure that tool is switched off and unplugged before removing or installing the blade. • Use the following planer blades. Part Nos. 793004-6 793007-0 793322-2 *P-04260 *P04276 *P-04282 *820044-1 *820045-1 *820043-1 Blades with * mark are available in European countries only. Consult your dealer or the Makita Service Center when purchasing blades. For tool with standard planer blades (Fig.
1923H (E) (’100. 6. 30) For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base. Below are some examples of proper and improper settings.
1923H (E) (’100. 6. 30) NOTE: When planing, move the tool with the edge fence flush with the side of the workpiece. Otherwise uneven planing may result. Max. shiplapping depth is 23 mm. MAINTENANCE Chamfering (Fig. 21, 22 & 23) Replacement of carbon brushes (Fig. 30, 31 & 32) To make a cut as shown in Fig. 21, align the ‘‘V’’ groove in the front base with the edge of the workpiece and plane it as shown in the Fig. 23. Nozzle assembly (optional accessory) (Fig.
1923H (Nl) (’100. 7.
1923H (Nl) (’100. 7. 6) 15. Vervang altijd gelijktijdig beide messen en klemplaten, aangezien anders het resulterende verlies van evenwicht trillingen kunnen veroorzaken, waardoor de gebruiksduur van het gereedschap verkort kan worden. 16. Wacht totdat de messen volledig tot stilstand zijn gekomen, alvorens de machine opzij te zetten. 17. Gebruik alleen Makita messen die in deze gebruiksaanwijzing zijn gespecificeerd. BEWAAR DEZE VOORSCHRIFTEN.
1923H (Nl) (’100. 7. 6) Voor de juiste mesinstelling Uw schaafvlak zal ruw en ongelijk worden, indien het mes niet correct is ingesteld. Het mes moet dusdanig gemonteerd worden dat de zijkant absoluut gelijk ligt ofwel parallel met het vlak van de achterzool. Onderstaand enkele voorbeelden van juiste en onjuiste instellingen. (A) Voor zool (beweegbaar) (B) Achterzool (vast) Correcte instelling Ofschoon dit zijaanzicht het niet toont, draaien de snijkanten van het mes perfect parallel met de achterzool.
1923H (Nl) (’100. 7. 6) Rabatten (Fig. 17, 18, 19 en 20) Aansluiten van een stofzuiger Gebruik de zijkantgeleider voor zijdelings schaven zoals afgebeeld in Fig. 17. Voor Europese landen en gebieden (Fig. 28 en 29) Voor schoon schaven sluit u een Makita-stofzuiger aan op uw machine. Monteer de zuigkop (bijgeleverd onderdeel) op de machine door gebruikmaking van de bijgeleverde schroeven. Sluit daarna een slang van de stofzuiger aan op de zuigkop (zie Fig. 29). Breng op het werkstuk de snijlijn aan.
1923H (12lang)(back) (’100. 6.
Makita Corporation Anjo, Aichi, Japan Made in Japan 883522E926