Cordless Driver Drill Equipped with Electric Brake MODEL 6217D MODEL 6237D MODEL 6317D MODEL 6337D MODEL 6347D I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. w w w. m a k i t a t o o l s .
SPECIFICATIONS Model 6217D Steel Capacities No load speed (RPM) 6237D 6317D 10 mm (3/8”) 6337D Wood 25.4 mm (1”) 32 mm (1-1/4”) 25.4 mm (1”) 32 mm (1-1/4”) 38 mm (1-1/2”) Wood screw 6 x 75 mm (1/4” x 3”) 6 x 75 mm (1/4” x 3”) 6 x 75 mm (1/4” x 3”) 6 x 75 mm (1/4” x 3”) 10 x 89 mm (3/8” x 3-1/2”) Machine screw 13 mm (1/2”) 13 mm (1/2”) 13 mm (1/2”) 13 mm (1/2”) 13 mm (1/2”) High Low 0 - 1,300/min. 0 - 1,300/min. 0 - 1,300/min. 0 - 1,300/min. 0 - 1,300/min. 0 - 400/min.
GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
Tool Use and Care 12. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 13. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 14. Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired. 15.
4. Be sure no one is below when using the tool in high locations. 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7. Do not leave the tool running. Operate the tool only when hand-held. 8. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 9. Some material contains chemicals which may be toxic. Take caution to prevent working dust inhalation and skin contact. Follow material supplier safety data.
5. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. 6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger. 7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a.
3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain.
FUNCTIONAL DESCRIPTION • 001892 2 1 Installing or removing battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click.
NOTE: • The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times.
001894 Switch action • 1 CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. 1. Switch trigger Electric brake This tool is equipped with an electric brake.
• 001897 Selecting action mode This tool has an action mode change lever. For drilling, depress the lock button and then slide the action mode change lever to the left ( symbol). For screwing, slide the action mode change lever to the right ( symbol) until it is locked. 1 2 If it is hard to turn the lever, first turn the chuck slightly in either direction and then turn the lever again. 1. Lock button 2. Action mode change lever • • 001898 1 2 3 1. Adjusting ring 2. Graduations 3.
001899 1 Installing or removing driver bit or drill bit Hold the ring and turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. 2 To remove the bit, hold the ring and turn the sleeve counterclockwise. 1. Sleeve 2. Ring 001900 1 When not using the driver bit, keep it in the bit holders. Bits 45 mm long can be kept there. 2 1. Bit 2.
Nominal diameter of wood screw (mm) 3.1 (1/8”) 3.5 (9/64”) 3.8 (5/32”) 4.5 (11/64”) 4.8 (3/16”) 5.1 (13/64”) 5.5 (7/32”) 5.8 (7/32”) 6.1 (15/64”) • Recommended size of pilot hole (mm) 2.0 - 2.2 (5/64” - 3/32”) 2.2 - 2.5 (3/32” - 3/32”) 2.5 - 2.8 (3/32” - 7/64”) 2.9 - 3.2 (7/64” - 1/8”) 3.1 - 3.4 (1/8” - 9/64”) 3.3 - 3.6 (1/8” - 9/64”) 3.7 - 3.9 (9/64” - 5/32”) 4.0 - 4.2 (5/32” - 11/64”) 4.2 - 4.
001902 1 • Always secure small workpieces in a vise or similar holddown device. • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Installing set plate (optional accessory) Model 6217D, 6317D only Always install the set plate when using battery cartridges 1200, 1202, 1201A. Install the set plate on the tool with the screw provided. 2 1. Screw 2.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the cleaner. Ni-Cd 2.
Memo 16
Cut First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc.
MAIL THIS PORTION Your answer to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Other ( Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( Home Center ) 2. Use of the product is intended for: ) 4.
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham Parkway Pelham, AL 35124 (205) 620-1791 COLORADO 11839 E. 51st Ave. Denver, CO 80239-2709 (303) 371-2850 KENTUCKY 1215 S. Hurstbourne Parkway Louisville, KY 40222 (502) 326-3740 NEW MEXICO 5805 Menaul Blvd. NE Albuquerque, NM 87110 (505) 881-4619 PUERTO RICO 200 Guayama St. Hato Rey, PR 00917 (787) 250-8776 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CONNECTICUT 508 Spring St.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.