Specifications

ManualsBrandsMakita ManualsPower saws2702

Model 2702 2703

2702x1 2703x1

Blade diameter .......................................... 210 mm 255 mm

Hole (arbor) diameter ................................ 25 mm 25 mm

Cutting capacities ...................................... 90°: 68 mm 91 mm

45°: 47 mm 63 mm

Table size (W x L) ..................................... 686 mm x 560 mm 686 mm x 560 mm

No load speed (RPM) ............................... 4,600 4,600

Dimensions (L x W x H) ............................ 560 mm x 686 mm x 458 mm 560 mm x 686 mm x 458 mm

Net weight ................................................. 18 kg 18 kg

Due to the continuing program of research and development, the specifications herein are subject to change without

prior notice.

Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only

be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can,

therefore, also be used from sockets without earth wire.

Table Saw

210 mm 2702

2702x1

255mm 2703

2703x1

SPECIFICATIONS

Summary of content (12 pages)

PAGE 1
Table Saw 210 m m 2702 2702x1 255m m 2703 2703x1 SPECIFICATIONS Model 2702 2702x1 Blade diameter .......................................... 210 mm Hole (arbor) diameter ................................ 25 mm Cutting capacities ...................................... 90°: 68 mm 45°: 47 mm Table size (W x L) ..................................... 686 mm x 560 mm No load speed (RPM) ............................... 4,600 Dimensions (L x W x H) ............................ 560 mm x 686 mm x 458 mm Net weight ...
PAGE 2
3 5 7 4 2 1 1 8 6 2 9 10 11 12 2 1 3 4 13 6 11 15 14 17 11 12 16 5 6 18 19 7 2 8
PAGE 3
23 9 20 21 3 22 9 24 25 10 26 27 11 90 90 45 12-A 45 12-B 12 25 30 28 13 29 14 3
PAGE 4
32 A B 33 29 31 15 16 34 2 30 35 17 18 19 20 37 18 38 21 4 22 36
PAGE 5
40 39 23 24 42 41 41 42 25 26 43 44 45 46 48 47 27 28 51 49 29 50 30 5
PAGE 6
Symbols The followings show the symbols used for the tool. Be sure that you understand their meaning before use. ❏ Read instruction manual.
PAGE 7
ENGLISH Explanation of general view 1 2 3 4 5 6 7 8 9 10 11 12 13 Offset wrench 13-22 Wrench 19 Loosen Inner flange Ring Saw blade Outer flange Hex nut Tighten Blade guard Spreader Pressure plate These two clearances should be equal.
PAGE 8
20. Check damaged parts Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.
PAGE 9
OPERATING INSTRUCTIONS The tool is shipped from the factory with the saw blade and blade guard not in the installed condition. Assemble as follows. CAUTION: Always unplug the tool before assembly. Installing saw blade CAUTION: • Use the following saw blade. Do not use saw blades which do not comply with the characteristics specified in these instructions. For Model Max. dia. Min. dia.
PAGE 10
Adjusting positive stops The tool is equipped with positive stops at 90° and 45° to the table surface. To check and adjust the positive stops, proceed as follows: Move the handwheel as far as possible by turning it. Place a triangular rule on the table and check to see if the blade is at 90° or 45° to the table surface. (Fig. 11) If the blade is at an angle shown in Fig. 12-A, turn the adjusting screws clockwise; if it is at an angle shown in Fig.
PAGE 11
Ripping MAINTENANCE CAUTION: • When ripping, remove the miter gauge from the table. • When cutting long or large workpieces, always provide adequate support behind the table. The support should be at the same height as the table. CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Switch the tool on and gently feed the workpiece into the blade along with the rip fence.
PAGE 12
Makita Corporation Anjo, Aichi, Japan 884129B8