Table Saw With Electric BraKe 210 mm (8-1/4") MODEL 2702Xl MODEL 2702 255 mm (10") MODEL 2703X1 MODEL 2703 iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii r_ INSTRUCTION DOUBLE INSULATION MANUAL iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii WARNING: For your personal safety, READ and UNDERSTAND SAVE THESE INSTRUCTIONS www.makita.com FOR FUTURE REFERENCE. before using.
SPECIFICATIONS MODEL Arbor hole 2702X1 2702 2703X1 2703 _8" Blade diameter 210rnrn (8-1/4") 255rnrn (10") Cutting capacities 90 450 68rnm (2-11/16") 91rnm (3-9/16") Maximum dado No loadspeed Tablesize capacity (RPM) (Wx L) 47mm (1-3/4") 63mm (2-1/2") 13 mm (1/2") • Manufacturer reserves the right to change specifications • Note: Specifications may differ from country to country. 4,600/min 686mrn x 560mrn (27" x 22") without notice.
For Your Own Safety Read Instruction Manual Before Operating Table Saw Save it for future reference GENERAL SAFETY PRECAUTIONS (For All Tools) 1. KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the tool's applications and limitations, as well as the specific potential hazards peculiar to it. 9. USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not designed; for example, don't use circular saw for cutting tree limbs or logs. 2.
16.REDUCE THERISKOF UNINTENTIONAL STARTING. Makesureswitchisin offposition before plugging in. 21. NEVERLEAVETOOLRUNNING UNATTENDED. TURNPOWER OFF. Don'tleavetooluntilit comesto a completestop. 17. USE RECOMMENDED ACCESSORIES. Consultthe owner'smanualfor recommended accessories. Theuseofimproper accessories maycauseriskof injuryto persons. 18.NEVER STAND ONTOOL. Seriousinjurycouldoccurif the toolis tippedorif thecuttingtoolis accidentally contacted. 22. Whenservicinguse onlyidentical replacement parts.
ADDITIONAL SAFETY RULES DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to table saw safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Wear eye protection. 2. Don't use the tool in presence mable liquids or gases. 10. NEVER wear gloves during operation. of flam- 3. NEVER use the tool with an abrasive cut-off wheel installed. 4. Check the blade carefully for cracks or damage before operation.
18.Donotperform anyoperation freehand. Freehand means usingyourhands tosupportorguidetheworkpiece, inlieuofa rip fenceormitergauge. 23.Don'tabusecord.Neveryankcordto disconnect fromreceptacle. Keepcord awayfromheat,oil, waterandsharp edges. 19. NEVERreacharoundor oversaw blade.NEVER reachfora workpiece until thesawbladehascompletely stopped. 24. Somematerialcontainschemicals whichmaybetoxic.Takecaution to preventworking dustinhalation andskincontact.Follow material supplier safetydata. 20.
ASSEMBLY The tool is shipped from the factory with the saw blade and blade guard not in the installed condition. Assemble as follows: CAUTION: • Always unplug the tool before assembly. Installing saw blade Remove the table insert on the table. Hold the outer flange with the offset wrench and loosen the hex nut counterclockwise with the wrench. Then remove the outer flange. 1. Wrench 2. Offset Wrench 3.
Installing blade guard CAUTION: • Before installing the blade guard, adjust the depth of cut to its maximum elevation. Insert the spreader between the blade guard mounting portion (stay) and the pressure plate. 3 1. 2. 3. 4. Blade guard Spreader Antikickback pawl Pressure plate 3 1 6 Tighten the hex bolts (A) with the offset wrench. The spreader installing location is factory-adjusted so that the blade and spreader will be in a straight line.
(18-1/16") 459 mm 334 mm 1 (13-1/8") 1.Hole diameter 8mm(5/16") 25mm (1" Positioning table saw Locate the table saw in a well lit and level area where you can maintain good footing and balance. It should be installed in an area that leaves enough room to easily handle the size of your workpieces. The table saw should be secured with four screws or bolts to the work bench or table saw stand using the holes provided in the bottom of the table saw.
Adjusting depth of cut The depth of cut may be adjusted by turning the handle. Turn the handle clockwise to raise the blade or counterclockwise to lower it. NOTE: • Use a shallow depth setting when cutting thin materials in order to obtain a cleaner cut. 1.Handle 1 1. Lock lever 2. Handwheel 3. Arrow pointer Adjusting bevel angle Loosen the lock lever counterclockwise and turn the handwheel until the desired angle (0 ° - 45 °) is obtained. The bevel angle is indicated by the arrow pointer.
After adjusting the positive stops, set the blade at 90 ° to the table surface. Then adjust the arrow pointer so that its right edge is aligned to the 0° graduation. 1 1. Arrow pointer Installing and adjusting rip fence Raise the grip of the rip fence. Install the rip fence on the table so that the fence holder engages with the guide rail. The rip fence can be secured by lowering the grip. 1. Fence holder 2. Guide rail 3.
CAUTION: • Always grasp the striped portion of the wrench when tightening the hex bolts. If you tighten the hex bolts while grasping the wrench further than the striped portion, the hex bolts may be damaged and/or an injury to your hand may result. 6. With the grip of the rip fence lowered, turn the adjusting nut clockwise to secure the rear end of the rip fence. Do not turn the adjusting nut clockwise excessively.
When operating the switch lever, it is convenient view it through the window area in the table. to CAUTION: • When not using the tool, remove the key and store it in a secure place. This prevents unauthorized operation. • Before plugging in the tool, always check to see that the switch lever actuates properly and returns to the "OFF" position. • Do not pull the switch lever hard without the key. This can cause breakage of the switch.
Push stick (H) 9.5 mrn 19 mm@_ (3/4) _ 130 rnm (5") 9.5 mm _'i;'_"_ Y I (50')mm g80 mm (15") \ A push stick can be easily made from a piece of plywood 19 mm (3/4") to 25 mm (1") thick. Cut out the hatched area on the stick and smooth edges with a file. (H) dimension should be less than 12.7 mm (1/2") so as to be thinner than the workpiece. 120 mT1 I 300 Tim(2") 6 ram (1/4") j 2 _ Push block Use a 19 mm (3/4") piece of plywood. I _ 50ram (2") .
Wood facing (rip fence) A wood facing should be used for operations when the blade comes close to the rip fence. Wood facing for the rip fence should be the same size as the rip fence. Make sure the bottom of facing is flush with the table surface. 1 1. No. 10 wood screws (long enough to penetrate halfway into facing) Crosscutting CAUTION: • When making a crosscut, remove the rip fence from the table. • When cutting long or large workpieces, always provide adequate support to the sides of the table.
Auxiliary wood facing (miter gauge) To prevent a long board from wobbling, fit the miter gauge with an auxiliary fence board. Fasten with bolts/nuts after drilling holes, but fasteners must not protrude from the face board. Ripping CAUTION: • When ripping, remove the miter gauge from the table. • When cutting long or large workpieces, always provide adequate support behind the table. DO NOT allow a long board to move or shift on the table.
3. Turn the tool on and gently feed the workpiece into the blade along with the rip fence. (1) When the width of rip is 150 mm (6") and wider, carefully use your right hand to feed the workpiece. Use your left hand to hold the workpiece in position against the rip fence. (2) When the width of rip is 65 mm - 150 mm (2-1/2" - 6") wide, use the push stick to feed the workpiece. 1.
MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning Clean out sawdust and chips from time to time. Carefully clean the blade guard and moving parts inside the table saw. Lubrication To keep the table saw in tip-top running condition, and to assure maximum service life, oil or grease the moving parts and rotating parts from time to time.
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. Dado head set (Part No. 191543-4) A dado is cutting a rabbet or a wide groove into the workpiece. The dado head set consists of two outside cutters, three inside cutters and paper washers.
Table insert (Part No. 317061-6) When cutting grooves 5/16% 3/8",7/16" or 1/2" use this table insert instead of the standard table insert. To install the dado head set, proceed as follows: 1. Turn the tool off and unplug it before installing. 2. Remove the blade guard with the spreader. 3. Install the dado head set with the teeth pointing down at the front of the table. 4. Use the chart below to select the proper cutters to obtain the various cutting widths.
NOTE: • When widths slightly greater than the above are required, fit the paper washers in between the inside and outside cutters to adjust the width. 1 2 3 5. Arrange the cutters so that the tips of the inside cutters are positioned at the gullets of the outside cutter. When more than one inside cutter is used, space the tips of the inside cutters equidistantly in relation to one another. Poorly spaced cutters may cause vibration and noise. 1, Inside cutter 2, Outside cutter 3.
Featherboards are used to keep the workpiece in contact with the rip fence and table as shown, and to stop kickbacks. 1 i • -2 _ /# 3 1. 2, 3, 4, "C"Clarnps Facing board Featherboard Push stick To install featherboards, proceed as follows: 1. Turn the tool off and unplug it. 2. Add 8" high flat facing board to the rip fence, the full length of the rip fence. 3.
1 1. Rabbet 2. First cut 3. Second cut 3 How to perform rabbeting 1. Remove blade guard. 2. Attach auxiliary fence to rip fence for cuts that run the length of the stock. Facing should be as high as the workpiece is wide. Adjust fence and blade to desired dimensions. 3. First cut: Hold board flat on table as in ordinary ripping. 4. Second cut: Set workpiece on its edge. (Use featherboards, push stick, push block and so on, using precautions, safety rules and guidelines for ripping or related work.) 5.
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Steel & Carbide-tipped saw blades Table/Miter saw blades For general purpose cuts for table and miter saws.
I I First-Class Postage Required o Post not without Office p_oper postage Makita U.S.A., inc.
Your answers to the following 1, Th_ [] product was, purchased Home Center ]Hardware/Lumber []hdustrial 1tom: 3, How d_d you _earn about th_ [] Magazine [] Radii) [] From DeaJer [] Exhibition [] Newspaper [] From Friend [] Store Display [] Previous [] Catalog [] Other( Other ( Supply ]Industrial _ _ntended 1or: 4, Most _avored points Maintenance Home Maintenance [] Hobby [] Other ( are appreciated.
CE 1-800-4-MAK]TA RETAIN THIS PORTION ALABAMA COLORADO 2365 Pelham Rat kway Pelham AL 35124 1183c_ E 51st Ave DenJe_ CO 80239 (205) 620 1791 (303) ,&RIZON,¢ 3707 E Broadway Rd Ste 6 _'hoenix AZ 85O4O _502_437 2350 ARKANS,¢S S11ackletol d Shopl_ng Center 240Soutl/ Sha_kleto_dRd St÷ C Utt_eao_k AR 72211 _50t_224:373_ CALIFORNIA 4185O OhristySt _remol/t O,€ _4:S3_ 5107 _5t0_557 9t_81 2709 371 2850 FLORIDA 620 Douglas Ave Suite t 302 AJtamol/teSprings FL 32714 _407_774 6OOO 75O East Sample Road _'o
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm, Some examples of these chemicals are: lead from bad=based paints, o crystalline silica from bricks and cement and other masonry products, and o arsenic and chromium from chemically=treated lumber, Your risk from these exposures varies, depending on how often you do this type of work, To reduce your exp
