Cordless Trimmer 114'' MODEL 3700D 1/4" MODEL 3700DW With Fast Charger INSTRUCTION MANUAL SPECIFI CAT I 0N S Model * 3700D Collel L h u c k CdpaclIy No l o a d speed Overall l e n g t h Net weight 114" 8,000 R l m n 165 mm 16 lj2"I 1 0 k g 12 2 I b s l Battery Cartridge 7000 M o d e l DC7100 Fast charger ~ Charging Voltage ~ 7 2 v time _ 1 Hr Input _ _ _ _ A C only 50 H r 60 H r _ _ D C 7 2 v ~~ ~ Dimensions IL x W x H i Net weight 1 4 5 m m x 80 m m x 61 m m 15 314'' x 3
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools i n damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry plugged-in tool with finger o n switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are tired. 18.
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, ( 2 ) battery, and (3)product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 7000. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow. 5.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not ,allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals w i t h the battery cover when the battery cartridge is not used. 5.
ADDITIONAL SAFETY RULES FOR CORDLESS TRIMMER 1. Be aware that this tool is always in an operating condition, because it does not have t o be plugged into an electrical outlet. 2. Handle the bits very carefully. 3. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. 4. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7.
Installing or removing battery cartridge 0Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the s e t plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. 0 0 To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the s e t plate back into place. Be sure t o close the set plate fully before using the tool.
Installing or removing trimmer bit CAUTION : Always be sure that the tool i s switched off and the battery cartridge is removed before installing or removing the bit. To install the straight bit 6, insert it all the way into the collet cone and tighten the collet nut securely with the two wrenches. To install the straight b i t 3, first insert the adapter all the way into the collet cone, then insert the bit all the way into the adapter. Tighten the collet nut securely with the two wrenches.
Adjusting side base This tool is equipped with an adjustable side base. To make the side base flush with the tool base, loosen the wing bolt and s e t the tool on a level place. Then tighten the wing bolt securely. Switch action To start the tool, move the slide switch up. Move it down to stop.
Operation o s e t the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the b i t attains full speed. Move the tool forward over the workpiece surface, keeping the tool base flush and advancing smoothly until the cutting is complete. 0 When doing edge cutting, the workpiece surface should be on the left side of the bit in the feed direction. (See the figure below.
Straight guide (optional accessory) The straight guide is effectively used for straight cuts when chamfering or grooving. Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. Attach the straight guide with the clamp screw (A). Loosen the wing nut on the guide and adjust the distance between the bit and the straight guide. A t the desired distance, tighten the wing nut securely.
Guide base - The wide base is effectively used for straight cuts when chamfering or grooving. Attach the guide base to the side base with the wing nuts and bolts. Adjust the distance between the bit and the side (A) of guide base by sliding the guide base. Then tighten the wing nuts securely. The max. distance is 25 mm ( I " ) . When chamfering, grasp the tool body with one hand and press the guide base down slightly with the other hand as shown in the figure.
Trimmer guide (Optional accessory) Trimming, curved cuts in veneers for furniture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Install the trimmer guide on the tool base with the clamp screw (A). Loosen the clamp screw (B) and adjust the distance between the bit and the trimmer guide by turning the adjusting screw (1 mm or about 3/64" per turn). At the desired distance, tighten the clamp screw (B) to secure the trimmer guide in place.
Templet guide (Optional accessory) CAUTION : For your safety, remove the bit before installing the templet guide. The templet guide providesa sleeve through which the bit passes, allowing use of the trimmer with templet patterns. To install the templet guide, loosen the wing bolts and raise the side base. Insert the templet guide onto the base so that the notch in the templet guide i s aligned with the small tab on the base.
Circle cutting base (Optional accessory) Various diameter circles can be easily cut with the cordless trimmer by using the optional circle cutting base. To attach the circle cutting base, you must first remove the standard base. This i s done by removing the base clamp screw and then removing the standard base from the trimmer body. The circle cutting base is then installed, using the same clamp screw. Be sure to tighten the clamp screw securely.
NOTE : The straight bit 3 is recommended to cut plaster board. MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge i s removed before attempting t o perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, a1way.s using Makita replacement parts.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Fast charger Model DC7100 Part No. 113086-6 Straight bit 6 Part No. 733195-1 Straight bit 3 Part No. 733197-7 . Wrench 17 Part NO. 781008-0 *Wrench 1 0 Part No.
Oct -31-'85 EN 6 mm (1/4") CORDLESS TRIMMER Model 37000 Note: The switch and other part configurations may differ from country to country.
MODEL 3 7 0 0 0 "5, ,& Oct -31-'85 DESCRIPTION O ":'M $fD EN DESCRIPTION MACHINE ~ 1 1 2 3 1 1 4 5 5 6 7 8 9 1 1 2 2 1 10 1 Housing Set (With Item 51 Motor Switch Pan Head Screw M4x22 IWith Washer) Housing Set (With Item 11 Hex Nu1 M 5 Fiat Washer 5 Wing Bolt M5x15 Screw M5x55 Flat Washer 5 08% Collet Nut Coilet cone Spindle Rubber Pin 4 Rubber Pin 4 Switch Lever Name Plate Battery Holder Note The switch and other part specifications.
P MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy kvery Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
oct -09 '87 us 114" TRIMMER Model 3700B Note The switch.
Nov.-25-'85 MODEL 37006 ITEM NO. 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 in 19 20 21 22 23 24 NO.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, f r e w t prepaid, to one of Makita’s Factory or Authorized Service Centers.