MODEL 4014NV INSTRUCTION MANUAL DOUBLE INSULATION SPEC1FlCATlONS I Caoacities Air pressure (water column) Air volume 5 6 0 mm 2.8 m3/min. (22") ~ ________~ N o load speed 0 - 16,000 Rlmin. ~~ 1 1 Overall length 430 mm (16-7/8") ~ Manufacturer reserves the right t o change specifications without notice. * Note: Specifications may differ from country t o country. I 1 Net weight 1.75 kg (3.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp 3. 4. 5. 6. 7. a. 9. IO. 11. 12. 13. 2 or wet locations. Keep work area well lit. Don't expose power tools to rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o 15. 16. 17. 18. 19. 20. see that keys and adjusting wrenches are removed from tool before turning it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT. Watch what you are doing, use common sense.
HOW TO USE Blowing For dust blowing, attach nozzle to blower outlet, turning clockwise to lock it in place. Dust suction For dust suction, fit nozzle onto suction inlet and dust bag onto blower outlet. After the bag fills with dust, empty the contents of the dust bag into a dust bin by releasing the fastener.
Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. A speed control screw i s provided so that tool speed can be changed a t the fully-pulled trigger position.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection and maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly, Replace when they wear down to about 6 mm (1/4") or less. Keep the brushes clean and free to slip in the holders. Both brushes should be changed a t the same time. Use only Makita carbon brushes. U 6mm (1/4") Loosen the screw and slide the cover plate aside.
Take out the worn brush, insert the new one and secure the brush holder cap. I % \Carbon bizhes TO maintain product SAFETY and RELIABILITY, repairs, any other maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. 0 Nozzle (Long size) (Part No. 421223-1) Nozzle (Part No. 421065-3) 8 Dust bag (Part No.
bug.- 25-'84 @-ftL(LKitcL US BLOWER Model 4014NV Note: The switch and other part configurations may differ from country to country.
MODEL 4014NV Sep.
P MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.