Vacuum Cleaner MODEL 406 (Dry type) INSTRUCTION MANUAL DOUBLE INSU LAT I0 N Peak air flow Sealed sunction Recoverable capacity Dimensions (L x W x H ) Net weight 3.0 m3”in. (106 cu.ft./min.) 2 , 1 0of0 mwater m (83”) 3 2 P ( 8 . 3 gal.) 4 7 8 mm x 4 2 2 mm x 699 mm (,8-,/8r, 16.5,8rr 27.112aa) 1 0 . 3 kg ( 2 2 . 7 1bs) Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country t o country.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNING reduce the risk of fire, electric shock, or -TO injury: 1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. 2. Do not use on wet surfaces. Do not expose rain. Store indoors. 3. Do not allow t o be used as a toy.
16. AVOID UNINTENTIONAL STARTING. Be sure switch is OFF when plugging in. 17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 18. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. 19. This appliance is provided with double insulation. Use only identical replacement parts. See instructions for Servicing of Double-Insulated Appliances. 20.
ADDITIONAL SAFETY RULES 1. This is a dry type cleaner. Do not attempt t o pick up liquids, sharp materials such as razors, needles, broken glass or the like. 2. Do not use close t o heat sources (stoves, etc.). 3.Do not fold, tug nor step on the hose. 4. Clean and service the cleaner immediately after each use t o keep it in tiptop operating condition. 5. Be kind to your cleaner. Rough handling can cause breakage of even the most sturdily built cleaner. 6.
Installing hose Insert the hose into the hose inlet and turn clockwise until fully secured. Hose inlet I Installing cloth filter Install the cloth filter on the tank. Always be sure that there is no gap between the gasket on the cloth filter and the tank after installing F T Cloth filter Tank -/ Switch action To start the cleaner, press the "ON" side of the switch. To stop, press the "OFF" side of the switch. Switch CAUTION: .Do not operate the cleaner for a long time with intake hole blocked.
Storage of accessories A wand holder (pipe holder) is equipped on the side of the cleaner t o keep the straight/bent wand (pipe) out of the way during vacuuming breaks. Both the straight wand (straight pipe) and bent wand (bent pipe) can be stored after use just by inserting them in the holes in the cleaner base.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning Clogged filters cause poor suction performance. Clean out the filters from time to time. To remove dust or particles adhering to the cloth filter, shake the frame bottom quickly several times. Moreover, occasionally wash the cloth filter in soapy water, rinse and dry thoroughly in the shade before use. Never wash filters in a washing machine.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. *Nozzle assembly Part No. 122512 4 *Bending pipe Part No. 192562-3 *Hose *Straight pipe Inner dia. 19 m m (3/4") Part No. 192108-5 (2.5 m: 8 ft.) Inner dia. 28 mm (1-1/8") Part No. 192278-0 (1.5 m: 4.
The following joints are available for use with some type Makita planers, belt sanders, miter saws, routers, etc. Joint name & configuration Applicable model Concrete Planer PC1100 Belt Sanders 9401, 9402 Elbow joint 32 Ass'y Part No. JPA 122273 Miter Saws 24008, LS 1400 m Joint 4 0 Ass'y Part No. JPA 122274 Planers 19008. N 19008. 1901 Nozzle 51 - 1 Part No. 191569-6 + Joint 55 Ass'y Part No. JPA 122275 Nozzle Part No. JPA 122276 + Joint 55 Ass'y Part No.
Aug.--23--'96 US VACUUM CLEANER Model 406 Note: The switch, noise suppressor and other part configurations may differ from country t o country.
MODEL 4 0 6 'LiM $fb Aug.
MAKlTA LIMITED ONE YEAR WARRANTY I Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.