Cordless Cutter 85 mm (3-3/8”) MODEL 4191D 003506 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
SPECIFICATIONS Model 4191D Blade diameter Cutting depth 85 mm (3-3/8”) 90° 0 - 24 mm (0 - 15/16”) 45° 0 - 18 mm (0 - 11/16”) No load speed (RPM) 1,000/min. Overall length 316 mm (12-1/2”) Net weight 2.1 kg (4.6 lbs) Rated voltage D.C. 12V Standard battery cartridges 1222,1233,1234,1235 • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country.
able for one type of battery may create a risk of fire when used with another battery. 5. Use battery operated tool only with specifically designated battery pack. Use of any other batteries may create a risk of fire. Personal Safety 6. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. 7.
22. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury. SPECIFIC SAFETY RULES USB070-1 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to cordless cutter safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1.
tion your body and arm in a way that allows you to resist KICKBACK forces. KICKBACK forces can be controlled by the operator, if proper precautions are taken. When wheel is binding, or when interrupting a cut for any reason, release the trigger and hold the tool motionless in the material until the wheel comes to a complete stop. Never attempt to remove the tool from the work or pull the tool backward while the wheel is in motion or KICKBACK may occur.
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD301-1 The followings show the symbols used for tool. V ....................... volts ................... direct current n ....................no load speed ˚ .../min................revolutions or reciprocation per minute IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1.
8. Do not incinerate the battery cartridge even if it is severely damaged or is com- pletely worn out. The battery cartridge can explode in a fire. 9. Be careful not to drop or strike battery. SAVE THESE INSTRUCTIONS Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge.
FUNCTIONAL DESCRIPTION • 001327 1 2 Installing or removing battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click.
003517 Bevel cutting Loosen the clamping screw on the bevel scale plate on the front of the base. Set for the desired angle (0° - 45° ) by tilting accordingly, then tighten the clamping screw securely. 1 2 1. Clamping screw 2. Bevel scale plate 003521 Sighting For straight cuts, align the A position on the front of the base with your cutting line. For 45° bevel cuts, align the B position with it. A B 1 1. Cutting line 003525 Switch action 1 • 2 1. Lock-off lever 2.
003531 Installing or removing diamond wheel To install the wheel, first loosen the bolt with the hex wrench and remove the bolt and the flange. Then mount the wheel, the flange and the bolt. The wheel should be mounted with the Makita name on the flange side. 1 2 3 1. Bolt 2. Flange 3. Diamond wheel 003532 2 Press the shaft lock so that the wheel cannot revolve. Use the hex wrench to tighten the bolt securely. To remove the wheel, follow the installation procedure in reverse.
003539 Attach the tank holder onto the motor housing. Tighten the screw (B) securely. 003540 Connect the cap on the end of the polyvinyl tube to the mouth of the tank. Turn the tank clockwise when making the connection. Then tighten the screw (A) securely to secure the tank. 1 1.
min (11-13/16”/min).) Also slow down as you complete a cut to avoid breaking or cracking the workpiece being cut. • CAUTION: Be sure to hold the workpiece firmly down on a stable bench or table during operation. • Do not twist or force the tool in the cut, or the motor may be overloaded or the workpiece may break. • Do not use the tool with the wheel in an upward or sideways position.
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. Ni-Cd 2. a) Take the battery to your nearest Makita Factory Service Center or b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.
Memo 14
Memo 15
Memo 16
Cut Stamp Timbre Makita Canada Inc.
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Tool Distributor Other ( ) Magazine/Newspaper Catalog From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( Features Power Size Other ( ) ) Price 5.
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: (Montreal) 6389 boul. Couture, St. Leonard, Quebec H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: (Montreal) 1140 Rue Bégin, Ville St.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres.