ENGLISH (Original instructions) INSTRUCTION MANUAL Circular Saw 5007N 5007NF 008671 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model 5007N/5007NF Blade diameter Max. Cutting depth 185 mm at 90° 63.5 mm at 45° 45 mm at 56° 35 mm No load speed (min-1) 5,800 Overall length 317 mm Net weight 5.2 kg Safety class /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country.
Power tool use and care 18. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 20.
GEB013-4 9. CIRCULAR SAW SAFETY WARNINGS Danger: 1. Keep hands away from cutting area and the blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. 2. Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece. 3. Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece. 4.
12. 13. To avoid kickback, do support board or panel near the cut. 000154 14. Lower guard may be retracted manually only for special cuts such as "plunge cuts" and "compound cuts". Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically. Always observe that the lower guard is covering the blade before placing saw down on bench or floor.
25. Fig. 1 26. Keep blade sharp and clean. Gum and wood pitch hardened on blades slows saw and increases potential for kickback. Keep blade clean by first removing it from tool, then cleaning it with gum and pitch remover, hot water or kerosene. Never use gasoline. Wear a dust mask and hearing protection when use the tool. SAVE THESE INSTRUCTIONS. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product.
NOTE: • When changing the positive stopper's position, loosening the lever and tilting the bevel angle to less than the desired stopper position number allows to change it. • When the arrow on the positive stopper points 22.5, the bevel angle can be adjusted 0 - 22.5°;when the arrow points 45, it can be adjusted 0 - 45°; when the arrow points 56, it can be adjusted 0 - 56°.
Use only the Makita wrench to install or remove the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the hex wrench to loosen the hex bolt counterclockwise. Then remove the hex bolt, outer flange and blade. To install the blade, follow the removal procedure in reverse. BE SURE TO TIGHTEN THE HEX BOLT CLOCKWISE SECURELY. • CAUTION: Do not apply impact to the lamp, which may cause damage or shorted service time to it.
blade and lead to dangerous kickback and possible serious injury. Release switch, wait for blade to stop and then withdraw tool. Realign tool on new cut line, and start cut again. Attempt to avoid positioning which exposes operator to chips and wood dust being ejected from saw. Use eye protection to help avoid injury. 1. Triangular rule 1 Rip fence (Guide rule) 1. Rip fence (Guide rule) 008683 Replacing carbon brushes 1.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Corporation 884791A9 12 www.makita.
