Cordless Drill Equipped with Keyless Chuck and Electric Brake 10 mm (318”) MODEL 60761) 10 mm (3/8”) MODEL 6 0 7 6 D W With Quick Charger INSTRUCTION SPECIFICATIONS Model 6 0 7 6 D With Reversing Switch 81 Battery Capacities Steel /Wood 10 mm 13/8“1 I I Wood screw i1 4.5” x 20mm (3116” x 3/4”1 Model D C 7 0 2 0 B Quick Charger Input A.C. only 50 Hz - 6 0 Hz No load speed (RPMI 6oo 1 I I I Dimensions IL x W x HI 2 1 0 m m x 48 mm x 1 9 0 m m 18-1/4” x 1-7/8” x 7-112”) output D.C. 7.2 V .
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1 . KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18.
IMPOMANT SAFETY INSTRUCTIONS (FOR BATTERY CHARGER) SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (11 battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow.
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (5OOF) or ABOVE 4 5 O C (113OFI. 3. Do not use charger in damp or wet locations. 4. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 5.
Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. Charging plug CAUTION: * T h e battery in your n e w tool is not fully charged. You will need to charge it before use. Do not operate the tool during charging. Overcharging more than 2 days considerably s h o r t e n s t h e battery service life. Always unplug the charger after completing the charge.
Holding tool Hold the tool as shown in the figure. When drilling a large diameter hole, hold the tool firmly with both hands. Switch action Move the reversing switch lever to the "FWD" position for clockwise rotation or the "REV" position for counterclockwise. To start the tool, simply pull the trigger. Release the trigger to stop. When the reversing switch lever is in the neutral position, the tool will not start even if you pull the trigger.
Drilling ope rat ion Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 0 Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer a t the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals.
MAINTENANCE CAUTION : Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. DISPOSING OF TOOL A nicad battery is built into the handle of this tool. Always remove it before disposing of the tool.
Recycling the battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle t h e battery: 1 . Remove the battery from the tool. Ni-Cd 2. (a) Take the battery to your nearest Makita Factory Service Center. or (b) Take t h e battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : T h e s e accessories or a t t a c h m e n t s are recommended for use with your Makita tool specified in this manual. T h e u s e of any other accessories or a t t a c h m e n t s might present a risk of injury t o persons.
Jan -14-’93 US 10 mm (3/8”) CORDLESS DRILL Model 6 0 7 6 D Note: The switch and other part configurations may differ from country to country.
J a n -14-'93 MODEL 6 0 7 6 D ,&, DESCRIPTION US "0" SDDESCRIPTION MACHINE 1 2 1 1 3 1 4 1 5 6 1 8 10 1 1 1 1 1 I Tapping Screw M3x20 Batter" Switch Name Plate Plane Bearing 3 Housing Set IWith Item 171 Cwunleraunh Her Soohel Scmw M5r21 Keyless Drill C h u c k Gear Plane Bearing 5 DC Motor 7 2 V Circuit Board 17 18 I 1 1 Gear COmDlete 1 3 - 5 8 Plane Bearing 3 Holder 6 Housing Set IWith Item 31 C0"CX Note The switch and other part specifications may differ from cnuntry to country 13
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.