Cordless Driver Drill MODEL 6041D MODEL 6076D MODEL 6176D 002864 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
SPECIFICATIONS Model Capacities 6041D 6076D 6176D Steel / Wood 10 mm (3/8”) 10 mm (3/8”) 10 mm (3/8”) Wood screw 4.5 x 20 mm (3/16” x 3/4”) 4.5 x 20 mm (3/16” x 3/4”) 4.5 x 20 mm (3/16” x 3/4”) 450/min. 600/min. 0 - 600/min. No load speed (RPM) Overall length 201 mm (7-7/8”) 210 mm (8-1/4”) 210 mm (8-1/4”) Net weight 0.82 kg (1.8 lbs) 0.94 kg (2.1 lbs) 0.97 kg (2.1 lbs) Output Charging time Model Battery Charger 6041D DC4100 6076D 6176D DC7020B Input D.C. 4.8 V A.C.
Electrical Safety Tool Use and Care 4. A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery. 12. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 5.
Service 21. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. 22. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE USC003-1 1. SAVE THESE INSTRUCTIONS- This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA rechargeable batteries. Other types of batteries may burst causing personal injury and damage. 4.
ADDITIONAL SAFETY RULES FOR CHARGER & TOOL 1. The charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (50°F) or ABOVE 40°C (104°F). 3. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 4.
FUNCTIONAL DESCRIPTION • 002059 CAUTION: Always be sure that the tool is switched off before adjusting or checking function on the tool. Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. 1 • CAUTION: The battery in your new tool is not fully charged. You will need to charge it before use. • Do not operate the tool during charging. • Overcharging more than 2 days considerably shortens the battery service life.
002074 Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the “FWD” position for clockwise rotation or the “REV” position for counterclockwise rotation. 1 When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. 1. Reversing switch lever 004021 • • Use the reversing switch only after the tool comes to a complete stop.
OPERATION Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger just as the screw bottoms out. If the trigger is not released, the screw may strip out the hole or the screw and/or bit may be damaged. NOTE: • Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged.
• A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. • Always secure small workpieces in a vise or similar holddown device. MAINTENANCE • CAUTION: Always be sure that the tool is switched off before attempting to perform inspection or maintenance.
EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. Ni-Cd 2. a) Take the battery to your nearest Makita Factory Service Center or b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.
Memo 12
Cut Stamp Timbre Makita Canada Inc.
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Tool Distributor Other ( ) Magazine/Newspaper Catalog From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( Features Power Size Other ( ) ) Price 5.
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: (Montreal) 6389 boul, Couture, St. Leonard, Quebec H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: (Montreal) 1140 Rue Bégin, Ville St.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres.
