Equipped with Electric Brake MODEL 6094D MODEL 6094DW With Fast Charger INSTRUCTION MANUAL SPEC IFICAT IONS Model 6094D No load speed Capacities Wood screw 5.5 mm x 55 mm (7132'' x 2~118") Machine screw I Battery Cartridge 9000 I lHr 6 mm 115164") 1 I High I 0 - 1,100 Rimin. I I Dimensions (L x W x H) Low I "R,,4," 243 mm x 58 mm x 262 m m 19-112" x 2~114" x 10-5116") I weight Net 1.6 k g 13.5 lbsl Model D C 9 1 0 0 Fast charger A C only 50Hz-60Hz I D C 9.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are tired. 18.
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2)battery, and (3)product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 9000. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow. 5.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything t o cover or clog the charger vents. 4. Do not short the battery cartridge: (11 Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out the set plate on the bottom of the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool.
Installing or removing driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge i s removed before installing or removing the bit. Slide the sleeve toward the motor and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. NOTE : I f the bit is not inserted deep enough into the sleeve, the sleeve will not return to i t s original position and the bit will not be secured.
Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. CAUTION : 0 Always check the direction of rotation before operation. Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool.
Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger as soon as the clutch cuts in. NOTE : Use the proper bit for the head of the screw that you wish to use. Make sure that the driver bit i s inserted straight in the screw head, or the screw and/or bit may be damaged.
I 3.5 mm x 20 mm (1/8" x 3/4") 4.5 mm x 20 mm W 1 6 ' x 3/4") ~~~~ Wood screws 5.1 mm x 35 mm (3/16' x 1 -3/8") "5.5 mm x 5 0 mm (7/32" x 2") (* . . , 400 Rlmin.
MA1NTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, reparis, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORI ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Phil Iips Slotted 0 12 V Fast charger Model DC9012 0 Drill chuck S10 Part No. 763061 -8 oChuck key S l O Part No. 763412-5 12 #3 Part No.
Dec-19-86 EN CORDLESS SCREWDRIVER Model 60941) Note: The switch and other part configurations may differ from country to country.
MODEL 60940 O ";'M Dec.-19-'86 AtD DESCRIPTION D:$ DESCRIPTION ~ 1 2 3 4 5 6 I 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 6 2 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Pan Head Screw M4x22 IWith Washer) Pan Head Screw M4x35 IWith Washer) Housing Set lWith Item 461 Guide Plate Cam Plate Pan Head Screw M5x12 Change Ring Ring Spring 12 Sleeve Compression Spring 13 Steel 8.
MAKmA LIMED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool freight prepaid, to one of Makita’s Factory or Authorized Service Centers.