CordlessEquipped Driver Drill with Electric Brake MODEL 62211) MODEL 6221DW With Fast Charger INSTRUCTION MANUAL SPECIFICATIONS Model 6221D I I Capacities Steel 10 mm (318") I Wood 15 mm (518") I Wood screw 5.1 mm x 35 mm 13/16, x 1-318") I Machine screw No load speed IRPM) mm 1114,,1 ~ 700 I Dimensions IL x W x H) 202 mm x 50 mm x 218 mm 17-15/16" x 1-31/32" x 8-19/32") weight Net 1.4 kg 13.1 lbsl ~~ t Voltage Input output Charging time 9.6 V A.C. onlv 50 Hz - 60 Hz D.C. 7.2 V.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool w i t h finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified o n the nameplate of the tool. A power source w i t h voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. I f in doubt, DO NOT PLUG IN THE TOOL. Using a power source w i t h voltage less than the nameplate rating is harmful t o the motor.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2.Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (21 battery, and (3)product using battery. 3.CAUTION - To reduce risk of injury, charge only MAKITA Battery Cartridge 9100.Other types of batteries may burst causing personal injury and damage. 4.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals w i t h the battery cover when the battery cartridge is not used. 5.
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge *To remove the battery cartridge, pull out Battery cartridge the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool.
Installing or removing driver bit or drill bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Hold the ring and turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. Sleeve To remove the bit, hold the ring and turn the sleeve counterclockwise.
Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work i s prolonged. Wait 20 - 30 seconds before resuming operation. CAUTION : Always withdraw the tool from the workpiece before resuming operation. If the tool cannot be withdrawn, hold the tool firmly when turning on the tool, to overcome a strong reaction.
NOTE : Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. 0 0 When driving wood screws, predrill pilot holes to make driving easier and to prevent splitting of the workpiece. See the chart. Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the marking. Then proceed as follows. 0 0 -8.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits Drill bits Part No. Size Phillips I Slotted I b n L, 7842 1 5-OA #5F #7F I I 784010-0A 784011-0A 784606-0A Square drill bit Phillips bit r 2 Part NO. 784201-5 I Size 1 L (mm) I No.
Fast charger Model DC9700 Part No. 1 13103-2 *Charger 1 2 V for car Model DC9112 Part No. 1131 10-5 Fast charger Model DC1201 Part No. 113126.0 Battery cartridge 91 00 Part No. 19201 9-4 Battery cover Part No.
Sep -08-'94 US CORDLESS DRIVER DRILL Model 6221D Note: The switch and other part configurations may differ from country to country.
MODEL 6221D AtD N:'E," Sep-O8-'94 DESCRIPTION 9 10 1 1 7 1 1 1 1 1 1 1 11 12 13 14 15 16 17 18 19 20 21 3 4 5 6 7 8 'r,',"ED DESCRIPTION MACHINE __ MACHINE ~ 1 2 Housing Set [With Item 401 Name Plate Tapping Screw BT4x18 Battery Holder Switch Lever Switch Lever set Plate 22 23 24 1 1 1 1 1 1 25 26 27 28 1 Spring 27 29 30 COmpreSSlOn Spilng 2 2 31 1 1 1 1 Washer IO 32 1 1 1 Thrust Needle Gauge 1023 Flat Washer 1 0 Slider t a m Plate Pan Head Screw M3x14 [With Washer1 Change Ring
P Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd 1 To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.
