Cordless Driver Drill MODEL 6260D MODEL 6270D MODEL 6280D 005216 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
SPECIFICATIONS Model 6260D 6270D Steel Capacities 10 mm (3/8”) Wood 21 mm (13/16”) Wood screw 5.1 x 38 mm (3/16” x 1-1/2”) 25 mm (1”) 25 mm (1”) 5.1 x 63 mm (3/16” x 2-1/2”) Machine screw 6 mm (1/4”) High 0 - 1,200/min. No load speed (RPM) 6280D Low 0 - 350/min. Overall length 192 mm (7-9/16”) Net weight 1.4 kg ( 3.1 lbs) 1.5 kg (3.3 lbs) 1.6 kg (3.5 lbs) Rated voltage D.C.9.6V D.C.12V D.C.14.
. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Electrical Safety 4. A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery. 5. Use battery operated tool only with specifically designated battery pack.
20. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool. SERVICE 21. Tool service must be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel may result in a risk of injury. 22. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual.
SYMBOLS USD301-1 The followings show the symbols used for tool. V ....................... volts ................... direct current n ....................no load speed ˚ .../min................revolutions or reciprocation per minute IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE ENC004-1 1. Before using battery cartridge, read all instruc- (1) Do not touch the terminals with any con- tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
FUNCTIONAL DESCRIPTION • 005217 1 2 Installing or removing battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click.
005219 A B 1 Reversing switch action This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. 1. Reversing switch lever • 005220 3 1 2 1. Low speed 2. High speed 3. Speed change lever • Use the reversing switch only after the tool comes to a complete stop.
or a piece of duplicate material to determine which torque level is required for a particular application. NOTE: • The adjusting ring does not lock when the pointer is positioned only halfway between the graduations. • Do not operate the tool with the adjusting ring set between the number 16 and the marking. The tool may be damaged. ASSEMBLY • 005222 1 3 2 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
C00143 Nominal diameter of wood screw (mm) Recommended size of pilot hole (mm) 3.1 (1/8”) 2.0 - 2.2 (5/64”- 3/32”) 3.5 (9/64”) 2.2 - 2.5 (3/32”- 3-32”) 3.8 (5/32”) 2.5 - 2.8 (3/32”- 7/64”) 4.5 (11/64”) 2.9 - 3.2 (7/64”- 1/8”) 4.8 (3/16”) 3.1 - 3.4 (1/8”- 9/64”) 5.1 (13/64”) 3.3 - 3.6 (1/8”- 9/64”) Drilling operation First, turn the adjusting ring so that the pointer points to the marking. Then proceed as follows.
MAINTENANCE • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal.
Memo 11
Memo 12
Cut Stamp Timbre Makita Canada Inc.
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Tool Distributor Other ( ) Magazine/Newspaper Catalog From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( Features Power Size Other ( ) ) Price 5.
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: (Montreal) 6389 boul. Couture, St. Leonard, Quebec H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: (Montreal) 1140 Rue Bégin, Ville St.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres.