Drill 10 mm (3/8") MODEL 6405 Variable speed I Reversing INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS Drilling capacities 10 mm (318") No load speed I 16 mm (518") Overall length (RPM) Wood Steel I 0 - 2,100 I 240 mm (9-7116") Manufacturer reserves the right t o change specifications without notice. * Note: Specifications may differ from country t o country. WARNING: For your personal safety, READ and UNDERSTAND before using SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONALSTARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified o n the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful t o the motor. ADDITIONAL SAFETY RULES 1.
Installing or Removing Drill Bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. To install the bit, place the bit in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure to tighten all three chuck holes evenly. To remove the bit, place the chuck key in one hole only and turn it counterclockwise. Then loosen the chuck by hand.
CAUTION : Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. 0 Always check the direction of rotation before drilling. 0 0 Use the reversing switch lever only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. When not operating the tool, keep the reversing switch lever in the neutral position.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons.
Feb.-21-'94 US 10 mm (3/8") DRILL Model 6405 Note: The switch and other part configurations may differ from country to country.
1 2 3 4 1 1 1 1 5 1 6 7 8 1 1 1 9 1 DrillChuck S10 GEAR ASSEMBLY Ball Bearing 8272 Housing Set IWith Item 171 NamsPlata Bell Bearing 6272 Fan 52 ARMATURE ASSEMBLY [With Item 7 91 Ball Beering 6072 - 10 11 12 13 14 15 16 17 18 1 2 2 1 1 1 7 1 1 Note: The switch and other part specifications may differ from country to country.
I I MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
