ENGLISH (Original instructions) INSTRUCTION MANUAL Angle Grinder 9067/9067S/9067L 9069/9069S 001011 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH SPECIFICATIONS Model 9067/9067S 9067L 9069/9069S Depressed center wheel diameter 180 mm 180 mm 230 mm Spindle thread M14 M14 M14 No load speed (n0) / Rated speed (n) 8500 min-1 6600 min-1 6600 min-1 Overall length 458 mm 458 mm 458 mm Net weight 4.2 kg 4.2 kg 4.2 kg Safety class /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country.
Power tool use and care 18. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 20.
2. 3. 4. 5. 6. 7. 8. 9. may fly away and cause injury beyond immediate area of operation. 10. Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and shock the operator. 11. Position the cord clear of the spinning accessory.
the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you. c) When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur.
20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. Use the specified surface of the wheel to perform the grinding. Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. Do not leave the tool running. Operate the tool only when hand-held.
For tool with the lock-off switch To prevent the switch trigger from accidentally pulled, a lock lever is provided. To start the tool, push in the lock lever and then pull the switch trigger. Release the switch trigger to stop. For tool with the lock on and lock-off switch To prevent the switch trigger from accidentally pulled, a lock lever is provided. To start the tool, push in the lock lever and then pull the switch trigger. Release the switch trigger to stop.
NEVER bang or hit grinding disc or wheel onto work. Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc. This can cause loss of control and kickback. NEVER use tool with wood cutting blades and other sawblades. Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury. • 1. Lock nut wrench 2. Shaft lock 1 • • 2 001089 • To remove the wheel, follow the installation procedure in reverse.
• • The tool and its air vents have to be kept clean. Regularly clean the tool's air vents or whenever the vents start to become obstructed. • • • Replacing carbon brushes 2 • • 1. Commutator 2. Insulating tip 3. Carbon brush • • • 1 • • 3 • • 001146 When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replaced.
Makita Corporation Anjo, Aichi, Japan 884183-773 12