MODEL 9200Y INSTRUCTION MANUAL SPEC IFICAT10 NS Sponge dia. 125 mm (5") I I Orbits per min. 7,000 I Dimensions (Dia. x Height) 114 mm x 95 mm 14-112" x 3-34',) I 1 * Manufacturer reserves t h e right t o change specifications w i t h o u t notice. Note: Specifications may differ from country t o country. Net weight ~ 0.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. 3. KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors should be kept away from work area. 4. STORE IDLE TOOLS.
15. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.
ADDITIONAL SAFETY RULES 1. Use only 12 volt DC power source, or the motor will be damaged. 2. Operate the tool only after removing mud and sand from the car body and sponge, or the car body will be scratched by mud and sand. 3. Do not wet the tool, or the tool will be damaged. 4. Do not bear down the tool excessively during operation. Smooth and even operation cannot be performed because the bottom of the sponge will not move correctly as designed. 5. Do not place the tool directly on the ground.
Installing sponge CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the sponge. Simply attach the sponge to the pad, using the Velcro sheet on the sponge and the pad. (Note) There is no problem even if the alignment of the sponge and the pad is slightly off. So you do not have to align the center of the sponge t o the center of the pad accurately when installing the sponge. Velcro \ \ Pad I Applying wax to sponge Apply wax t o the entire surface of sponge
Operation 1. Waxing Switch on the tool. Move the tool slowly over the work surface with front t o back, side to side movement while applying light pressure t o the tool so that wax will be applied t o the work surface thin and evenly. r Apply light pressure a Move slowly (Note) *Do not bear down the tool excessively during operation. Smooth and even waxing cannot be performed because the bottom of the sponge will not move correctly as designed. *The tool may become hot during operation.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection and maintenance. After use Always remove the sponge from the tool and wash the sponge in detergent solution. Dry the sponge thoroughly in a breezy shaded area. (Note) If you do not wash the sponge after each use, the wax absorbed in the sponge will dry and the sponge will become heavier, less porous and dirty. This could cause greater vibration of the tool, resulting poor finish.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. *Spatula Part No. 414599-3 Waxing sponge Part No. 794498-8 Q Plastic case Part No.
Aug.-22-'91 US WAX-MATE Model 9200Y P Note: The switch and other part configurations may differ from country to country.
MODEL 92OOY Mar.-14-'90 MACHINE 4 5 1 6 1 1 1 1 Tapping Screw BT 4x35 Housing Set 1Wtth Item 81 Switch DC Motor 12 '4. Ball Bearing 609LB Cushion Rma 7 8 1 1 Bumper 9 1 1 Name Plats Pad Cord Foot 1Ai 10 11 12 1 2 Note: The switch and other part specifications may differ from country to country.
P MAKCTA LIMED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
