Electronic Sander Polisher 180 mm (7") MODEL 9207SPC INSTRUCTION MANUAL DOUBLE INSULATION SPEC1FICATIONS N o load speed 1,500 - 2,800 R/min. Overall length Net weight Spindle thread 4 7 0 m m (18-1/2") 3.5 kg (7.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. -1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
0 - 25 26 - Ampere Rating More Not More Than Than 0 - 6 - 10 12 - 6 10 12 16 50 51 - 100 101 - 150 AWG 18 18 16 14 16 16 16 12 ;: I 14 12 14 12 Not Recommended 21. REPLACEMENT PARTS. When servicing, use only identical replacement parts. 22. POLARIZED PLUGS. To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified o n the nameplate of the tool. A power source w i t h voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful t o the motor. SAVE THESE INSTRUCTIONS.
HOW TO USE Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation without having to keep your finger on the tirgger, just pull the trigger and then push in the lock button with your thumb. To stop the tool from the lock position, simply pull the trigger again and release it. I I Fig. 1 Speed changes If the knob on the switch lever in front is turned to the "H" setting, the high speed i s obtained; if set t o the "L" setting, the low speed results.
CAUTIONS : 1. Always wear safety glasses and mask during operation. 2. Grip the tool firmly with both hands. 3. Do not touch the rotating abrasive disc. 4. When sanding metal surfaces, be careful of the flying sparks. Handle tool in terms of the direction they fly. FOR USE AS A SANDER For disc sanding, assemble tool as seen a t right. Abrasive diJc Fig. Hold the spindle firmly with the wrench. Put on the rubber pad and all, then tighten lock nut using the lock nut wrench, turning clockwise.
FOR USE AS A POLISHER For polishing operation, assemble the tool as a t right. Hold the spindle firmly with the wrench 17. Put on the rubber pad, then tighten lock nut using the lock nut wrench provided, turning clockwise. Next, put wool bonnet on, fastening it securely with strings as snugly as possible, near the center. Tuck in the loose ends of the cord in between the wool bonnet and the rubber pad. .-. .-... Fig. C -,A I ITlnN: Loose cord ends when using the wool bonnet can be very dangerous.
MAINTENANCE CAUTION : Always be sure that the tool i s switched off and unplugged before attempting to perform inspection and maintenance. 0 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. I / I Limit mark Fig.
ACCESSORIES CAUTION: The accessories specified in this manual are recommended for use with your Makita Electronic Sander Polisher. The use of any other accessories might be hazardous. 0 Wool bonnet 180 Lock nut wrench 28 (Part No. 743404-0) (Part No. 782413-4) Abrasive disc Wrench 17 (Part No. 781008-0) Grit I 16 20 24 30 50 80 100 120 0 Part No. 742067-9 742068- 7 742069- 5 742089-9 742070-0 742071-8 742090-4 742091-2 I Discs Der . oka . - Rubber pad 170 ( P a r t No.
180 mm (7") ELECTRONIC SANDER POLISHER Model 9207SPC Note: The switch, noise suppressor and other part configurations may differ from country to country.
'LtM At! M m 1 E 1 DESCRIPTION 'LtM $tD DESCRIPTION MACHINE Woodruff Key 3 F I E L D ASSEMBLY (With Garter Spring x 21 28 1 29 1 LockNut 16-48 P H. Screw M 4 x 4 5 (With Washer) Label Name Plats 2 2 H.
MAKEA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
