Belt Sander I00 mm (4") MODEL 9401 INSTRUCTION MANUAL Specifications Belt size 100mmx610mm (4") x (24") Belt speed I 1 I AMPS (115V) 350m (1,150ft.) lmin' I Overall length 1 I 3 7 4 mm (14-3/4") 1 1 ':E?,, Power w!egtht 7.3 kg (16.1 Ibs) 1 (12Jft.) Manufacturer reserves the right t o change specifications of parts and accessories without notice Note: Specifications of parts and accessories may differ from country t o country.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. SAVE THESE INSTRUCTIONS.
How to use 1. Switch action To start the tool, simply pull the trigger. Release the trigger t o stop. For continuous operation without having t o keep your finger on the trigger, just pull the trigger and then push in the lock button with your thumb. To stop the tool from lock position, just pull the trigger again and release it. 2.
0 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down t o the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes. / Limit mark Optional accessories CAUTION: The accessories specified in this manual are recommended for use with your Makita Belt Sander. The use of any other accessory might be hazardous.
lOOmm(4") BELT SANDER Model 9401 Note: The switch, noise suppressor, plug and other part configurations may differ from country to country.
MACHINE MACHINE 1 1 Dust Collector Bracket Knob 55 4 P. H. Screw M5xlB [With Washer) 39 40 1 2 1 Retaining Ring S-12 Tension Roller Arm 3 1 Fan 74 41 1 4 1 P. H . Screw M5x12 [With Washer) 42 1 Cup Washer 12 5 1 separator 43 1 6 7 1 2 Dust Collector Cower P. H. Screw M5x25 (With Washer1 Tension Roller (With Plane Bearing 12 & Swngs S h w t l 44 1 CupWasher 12 8 2 P. H. Screw M5x28 (With Werharl 45 1 Tension Roller Shaft 9 1 Ball Bearing 6200LLB 46 3 P. H.
MAKlTA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.