a Angle Grinder 100 mm (4”) 100 mm (4”) 115 mm (4-112”) MODEL 9 5 6 0 C V MODEL 9 5 6 3 C V MODEL 9 5 6 1 C V 115 mm (4-112”) 125 m m (5”) MODEL 9 5 6 4 C V MODEL 9 5 6 5 C V INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS MODEL 9560CV 9563CV 1 1 I 9561CV ___ 9565CV I No load speed (RPM) 2,800 2,800 10,5001min 10,5001min. ~ 2.800 - 10,5001min 2,800 10,50O/min. ~~ I 1 I I Overall lenqth 289 m m ( 1 1 318”) 2 9 9 mm ( 1 1 - 3 1 4 ” ) I 1 1 Net weiaht 1 7 k q ( 3 . 7 Ibs) 1 .
GENERAL SAFETY RULES USAooz-i (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 14.
Specific Safety Rules USBOOS-l 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3.Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its o w n cord.
SYMBOLS The followings show the symbols used for tool. v volts A Hz .................................... .................................... .................................... ? ,. .................................... alternating current b .................................... no load speed H .................................... Class II Construction .../min ...................................
FUNCTIONAL DESCRIPTION Switch action CAUTION: Before plugging in the tool, always check to see that the switch actuates properly and returns to the "OFF" position when the side of the switch lever is depressed. To start the tool, slide the switch lever to "I" position. For continuous operation, depress the front of the switch lever and then slide to "I" position as above. The switch is locked on the position for continuous operation.
ASSEMBLY Installing and removing wheel cover Installing Pull the lever in the direction of the arrow after loosening the screw. Install the wheel cover on the bearing box by adjusting the convex of the wheel cover to the concave of the bearing box. Turn the wheel cover by 180 degrees. Fasten it with the screw after pulling the lever the direction of the arrow.
Installing or removing the depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. Lock nut e -a Depressed Inner flange To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.
WARN1NG: It should never be necessary to force the tool. The weight of the tool applied adequate pressure. Forcing and excessive pressure could cause dangerous when wheel breakage. Continued use of a worn-out wheel may result in wheel explosion and serious personal injury. Depressed center wheel should not be used after it has been worn down to 75 mm (3") in diameter for Models 9560CV, 9563CV or 90 mm (3-1/2") for Models 9561CV, 9564CV and 9565CV in diameter.
ACCESSORIES CAUTION: These accessories or attachments are recommendedfor use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. @ Wheelcover PanNo. I For Model Q Inner flange I Size I 45 @ Depressed center wheels Pan No. 741402-8 18ulk) I I Size I I Pat NO. 74203808 7420380C 9563cv 40 4-1/2" x 5B" x 7 W 7943314.
@ Rubberpad (For abrasive disc) Part No. For Model 743036-3 9565CV 9565CV 743015-1 @ Abrasive discs @ Wire cup brush 75 Part No 74203603 I 9565CV Diameter Per pkg For Model @ Wire bevel brush 85 9560CV 4' 9563CV 8 Wheel guard assembly (For cut-off wheel) For Model 9560CV. 9563CV Part No.
@ Cut-off wheel Grit Wheels per pkg. For use For Model 724104-110 Pan No. 4" x 3/32" x 5"' Size 36 10 For masonry and concrete. 724107-510 4" x 5/64" x 5B" 46 10 For steel and cast iron. 9560cv 9563CV Knot-Type Wire cup brush Knotted-Twist Wire cup brush 9564CV Pan No. I 743212-A I Part No. I For Model 9561CV 9564CV 9565CV Lock nut wrench Stringer Bead Twist Wire brush wheel ForModel 0 9561CV 9565CV 743213-E 9565CV Full Cable Twist Wire brush wheel Part No.
+ 57 56 55 54 50 48 G 47 @- 46 13
ITEM NO. DESCRIPTION 1 PIN CAP 2 COMPRESSION SPRING 8 3 GEAR HOUSING COMPLETE HEX. NUT M6 4 FLAT WASHER 6 5 6 SPIRAL BEVEL GEAR 1 1 7 LOCK SPRING 12 RETAINING RING S-12 8 9 BALL BEARING 6001LLB FLAT WASHER 12 10 GEAR HOUSING COVER 11 FAN 57 12 13 ARMATURE ASSY INC. 12.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of Califomia] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: 0 Lead from lead-based paints, 0 Crystalline silica from bricks and cement and other masonry products, and 0 Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.