Disc Grinder 180 mm ( 7 ” ) MODEL 9607BL 230 mm (9”) MODEL 9609B INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS MODEL I 9607BL I 6,000 96098 [ 6,000 No load speed (RPM) 1 Overall length I 450 mm (1,7-314“1 1 450 mm (47-314”) 1 I I Net weight I Spindle thread 6.0 kq 113.2 Ibsl I 5/8-11 UNC 6.3 kg (13.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don’t use power tools in damp or wet locations. Keep work area well lit. Don’t expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18.
ADDITIONAL SAFETY RULES 1. Keep guards in place. 2. Use only wheels having a maximum operating speed at least as high as “No Load RPM” marked on the tool’s nameplate.,When using depressed center wheels, be sure t o use only fiberglass-reinforced wheels. 3. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 4. Use only flanges specified for this tool. 5.
Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. Lock nut Inner flange I To remove the wheel, follow the installation procedure in reverse.
Switch action TO start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. ' ' / Lock button 1 CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Operation Hold the tool firmly.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes. Limit mark Use a screwdriver to remove the brush holder caps.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Wheel cover Part NO. Inner flange 89 (For depressed center wheel) Part No.
@ 0 Sanding lock nut 48 Abrasive disc (10 per pkg) (For abrasive disc) Part No. 224517-1 @ 794091- 8 Wire cup brush 16 794092-6 794093-4 794218-0 180 (7") 794094-2 794095-0 794220-3 I 1 794221-1 @ 80 100 120 Flexible grinding wheel ( I O per pkg) 180 x 3 x 22 (7" x 1/8" x 7/8") 794234-2 794235-0 794236-8 Diameter 4" 6' 0 Lock nut wrench 28 Part No. 782412-6 (For 9609B) Part No. 782413-4 (For 9607BL) 0 Grip 37 Part No.
Jan.-26-'90 US DISC GRINDER 180 mm (7") Model 9607BL 230 mm (9") Model 9609B Note: The switch and other part configurations may differ from country to country.
MODEL 9607BL 96098 IT$ AiD Jan AiD DESCRIPTION MACHINE 26-90 US DESCRIPTION MACHINE ~ ~ 1 2 3 4 2 1 4 1 5 6 7 1 1 1 9 1 10 11 12 13 14 15 16 1 1 17 18 19 20 21 22 23 24 25 1 1 3 1 1 AR 1 4 1 1 1 1 2 2 26 21 1 28 1 29 30 31 32 33 1 1 Pan Head Screw M6x16 IWith Washer1 Tool Rest Pan Head Screw M5x25 IWilh Washer1 Retaining Ring R 12 Pin 6 Compression Spring 7 Gear Housing Ball Bearing 629LB Flat Washer 9 Spindle Lock Bush Retaining Ring S - 17 Spiral Bevel Gear 58 Pan Head S
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.