Disc Grinder 180 mm (7”) 230 mm (9”) MODEL 9607BL MODEL 9609B INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS MODEL No load speed (RPM) 9607BL 6,000 96098 6,000 Overall length I 450 mm (1~7-3/4”1 450 mm 1117-3/4”) Net weight I Spindle thread 6.0 kg (13.2 Ibs) 518- 11 UNC 6.3 kg (13.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are tired. 18.
ADDITIONAL SAFETY RULES 1. Keep guards in place. 2. Use only wheels having a maximum operating speed at least as high as "No Load RPM" marked on the tool's nameplate.,When using depressed center wheels, be sure t o use only fiberglass-reinforced wheels. 3. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 4. Use only flanges specified for this tool. 5.
Installing or removing depressed center wheel CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. Lock nut Depressed center whpe _. Inner flange To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. 1 Lock button CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Operation Hold the tool firmly.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes. Limit mark Use a screwdriver to remove the brush holder caps.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should b e used only in the proper and intended manner. @ @ Wheel cover Part No. Size (mm) 164396-4 180 (7") 164397-2 230 19') For Model 9607BL 96098 @ Inner flange 89 (For depressed center wheel) Part No.
@ 0 Sanding lock nut 48 Abrasive disc (10 per pkg) (For abrasive disc) Part No. 22451 7- 1 Part No 794091-8 794092-6 794093-4 794218-0 794094-2 794095-0 794220-3 794221-1 @ Grit Diameter lmml 16 20 24 30 50 80 100 120 180 17") Part No. [ I Grit 36 I Part No 0 Size (mml I 794234-2 794235-0 Wire cup brush 743207 2 743206 A 743206 B Flexible grinding wheel ( 1 0 per pkg) 794265-1 0 0 180 x 3 x 22 (7" x li8" x 718") I Diametei 4" 6' Lock nut wrench 28 Part No.
Jan.-26-90 US DISC GRINDER 180 mm (7") Model 9607BL 230 mm (9") Model 9609B Note: The switch and other part configurations may differ from country to country.
MODEL 9607BL. 96098 Jan MACHINE __ 1 2 3 4 5 6 1 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 2 1 4 1 1 1 1 1 1 1 1 1 3 1 1 A.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
