ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Random Orbit Sander BBO140 BBO180 012886 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model BBO140 Paper size Low speed Orbits per minute(min-1) BBO180 125 mm 7,000 Middle speed 9,500 High speed 11,000 Dimensions 175 mm x 123 mm x 153 mm Net weight 1.6 kg 1.7 kg Rated voltage D.C. 14.4V D.C. 18V Standard battery cartridge BL1430 BL1830 • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. 21. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 22. Keep cutting tools sharp and clean.
GEB021-4 5. SANDER SAFETY WARNINGS 1. 2. 3. 4. 5. 6. 7. 8. Always use safety glasses or goggles. Ordinary eye or sun glasses are NOT safety glasses. Hold the tool firmly. Do not leave the tool running. Operate the tool only when hand-held. This tool has not been waterproofed, so do not use water on the workpiece surface. Ventilate your work area adequately when you perform sanding operations. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact.
Battery protection system (Lithium-ion battery with star marking) FUNCTIONAL DESCRIPTION • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 1. Star marking 1 Installing or removing battery cartridge 1 2 1. Red indicator 2. Button 3. Battery cartridge 012128 Lithium-ion batteries with a star marking are equipped with a protection system.
Emptying dust bag Speed mode Number of rotations High 11,000 Middle 9,500 Low 7,000 Usage 1. Dust nozzle Regular sanding Finish sanding 1 Polishing 012897 NOTE: • The table shows standard applications. They may differ under certain conditions. 003323 When the dust bag is about half full, switch off the tool, and remove the dust bag from the tool. Then remove the dust nozzle from the dust bag after unlocking the dust nozzle by turning it slightly counterclockwise.
1 You can choose one of 12 directions of the skirt in accordance with your purpose. 1. Dust box 2. Dust nozzle 1. Skirt 2. Screw 1 2 009095 Make sure that the logo on the cardboard lip and the logo on the dust nozzle are on the same side, then install the dust nozzle on the dust box. 2 012885 To remove the skirt, remove the screw and remove the skirt with slightly opening it for both sides. Removing dust box and paper filter bag 1. Skirt 1. Latch 2.
Using the tool with the pad edge contacting the workpiece may damage the pad. Hold the tool firmly. Turn the tool on and wait until it attains full speed. Then gently place the tool on the workpiece surface. Keep the pad flush with the workpiece and apply slight pressure on the tool. • 2. 1. Felt pad CAUTION: The sanding pad rotates clockwise during the loaded operation, but it may rotate counterclockwise during the no-load operation. 1 012883 Use an optional felt pad.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Corporation 885120-9 12 www.makita.
