Cordless Angle Nut Runner MODEL BFL300F MODEL BFL400F 005735 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
SPECIFICATIONS Model Fastening torque BFL300F BFL400F Hard joint 16 - 30 N • m (142 - 266 in • lbs) 25 - 40 N • m (221 - 354 in • lbs) Soft joint 16 - 30 N • m (142 - 266 in • lbs) 25 - 40 N • m (221 - 354 in • lbs) Square drive 9.5 mm (3/8”) 9.5 mm (3/8”) No load speed (RPM) 400 /min. 260 /min. Dimensions (With Battery Cartridge BH1427) 506 mm x 73 mm x 104 mm (19-15/16” x 2-7/8” x 4-1/8”) 510 mm x 73 mm x 104 mm (20-1/16” x 2-7/8” x 4-1/8”) Net weight (With Battery Cartridge BH1427) 2.
Electrical safety 4. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 5. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. 6. Do not expose power tools to rain or wet conditions.
before use. Many accidents are caused by poorly maintained power tools. 21. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 22. Use the power tool, accessories and tool bits etc. in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.
. Do not leave the tool running. Operate the tool only when hand-held. 6. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 7. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
. Do not store the tool and battery cartridge in 7. Do not incinerate the battery cartridge even if it locations where the temperature may reach or exceed 50°C (122°F). is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. SAVE THESE INSTRUCTIONS Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged.
FUNCTIONAL DESCRIPTION • 005736 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 1 • Always switch off the tool before insertion or removal of the battery cartridge. 2 3 • To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge.
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. 005739 Lighting up the lamps 2 • 1 1. Lamp 2. LED indicator Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled.
LED indicator / Beeper Led indicator / Beeper on the tool shows the following functions.
005750 Adjusting the fastening torque When you wish to drive machine screws, wood screws, hex bolts, etc. with the predetermined torque, adjusting the fastening torque as follows. 1. First remove the battery cartridge from the tool. 2. Loosen and remove the screw that secures ring. 1 3. Rotate the ring in the front of the tool by hand so that a hole can be seen below the ring. 1. Screw 005740 1 7 6 2 3 1. 2. 3. 4. 5. 6. 7.
ASSEMBLY • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Selecting correct socket There are different types of sockets for some models depending on applications. Choose and install a correct socket for your application.
MAINTENANCE • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES • CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual.
Cut Stamp Timbre Makita Canada Inc.
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Tool Distributor Other ( ) Magazine/Newspaper Catalog From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( Features Power Size Other ( ) ) Price 5.
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: (Montreal) 6389 boul. Couture, St. Leonard, Quebec H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: (Montreal) 1140 Rue Bégin, Ville St.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres.
