ENGLISH INSTRUCTION MANUAL Cordless Auto Feed Screwdriver BFR540 BFR550 BFR750 008261 WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH SPECIFICATIONS Model BFR540 Screw strip BFR550 4 x 25 - 55 mm No load speed (min-1) BFR750 4 x 45 - 75 mm 4,000 Overall length 424 mm 464 mm Net weight 2.1 kg 2.3 kg 2.3 kg Rated voltage D.C. 14.4 V D.C. 18 V D.C. 18 V Standard battery cartridges BL1430 BL1830 • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Note: Specifications may differ from country to country.
Personal Safety 9. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. 10. Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. 11.
20. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 21. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 22. Use the power tool, accessories and tool bits etc.
even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 ゚ C (122 ゚ F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. Be careful not to drop or strike battery. 6. 7. 8. out of the tool, causing injury to you or someone around you. Do not use force when inserting the battery cartridge.
Adjusting the driving depth When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. 1. Stopper base 2. Casing 3. Adjusting knob 5mm 1 • 2 • 3 A B • 008124 CAUTION: Always check the direction of rotation before operation. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
Folding screw guide 1. Feeder box 2. Screw strip 3. Screw guide 1 2 3 008290 008289 1. Driving position Screw guide is foldable. Folding the screw guide allows space used for storage to be minimal. 1 Carry hook The carry hook is convenient for temporarily hooking the tool. It can be installed on either side of the tool. When removing the carry hook, widen it by pressing its right ends ON BOTH SIDES in the directions of arrow (1) and raise it in the direction of the arrow (2). 008288 1.
Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Loosen the thumb screws which secure the casing. Pull out the casing in the direction of the arrow. Always hold the tool squarely against the driving surface. Holding it at an angle may damage the screw heads and cause wear on the bit. This may also lead to poor fastening.
1. Carbon brush cap 1 006817 Make sure that the carbon brush caps have fit into the holes in brush holders securely. 1 1. Hole 2. Carbon brush cap 2 006304 Reinstall the front cover and tighten two screws securely. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
Makita Corporation Anjo, Aichi, Japan 884724-220 12