ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Circular Saw BHS630 012092 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model BHS630 Blade diameter Max. Cutting depth 165 mm at 90° 66 mm at 45° 46 mm No load speed (min-1) 3,100 Overall length 346 mm Net weight 3.5 kg Rated voltage D.C. 18V • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country.
electric shock if your body is earthed or grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 8. When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Service 28. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 29. Follow instruction for lubricating and changing accessories. 30. Keep handles dry, clean and free from oil and grease. Power tool use and care 17. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 18.
8. 9. of the saw will run eccentrically, causing loss of control. Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.
12. 13. 14. Lower guard may be retracted manually only for special cuts such as "plunge cuts" and "compound cuts." Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically. Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path.
25. 26. Keep blade sharp and clean. Gum and wood pitch hardened on blades slows saw and increases potential for kickback. Keep blade clean by first removing it from tool, then cleaning it with gum and pitch remover, hot water or kerosene. Never use gasoline. Wear a dust mask and hearing protection when use the tool. 8. 9. SAVE THESE INSTRUCTIONS. Tips for maintaining maximum battery life 1. SAVE THESE INSTRUCTIONS. 2.
• FUNCTIONAL DESCRIPTION • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 1 1. Red indicator 2. Button 3. Battery cartridge • 2 Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the trigger switch on the tool and stop the application that caused the tool to become overloaded.
NEVER tape down or defeat purpose and function of lock-off lever. • Sighting 2 1. Cutting line 2. 45 position 3. 0 position 4. Screw 5. Top guide 1 Lighting the lamp • CAUTION: Do not look in the light or see the source of light directly. 1. Light 5 4 3 1 012106 Only to turn on the light, pull the switch trigger without pressing the lock-off lever. To turn on the light and run the tool, press the lock-off lever and pull the switch trigger with the lock-off lever being pressed.
To remove the blade, press the shaft lock so that the blade cannot revolve and use the wrench to loosen the hex bolt counterclockwise. Then remove the hex bolt, outer flange and blade. To install the blade, follow the removal procedure in reverse. BE SURE TO TIGHTEN THE HEX BOLT CLOCKWISE SECURELY. 1. Hose 2. Vacuum cleaner 1. Hex bolt 2. Outer flange 3. Saw blade 4. Inner flange 2 1 2 012149 When you wish to perform clean cutting operation, connect a Makita vacuum cleaner to your tool.
tool back to the cut line. Doing so may bind the blade and lead to dangerous kickback and possible serious injury. Release switch, wait for blade to stop and then withdraw tool. Realign tool on new cut line, and start cut again. Attempt to avoid positioning which exposes operator to chips and wood dust being ejected from saw. Use eye protection to help avoid injury. This adjustment has been made at the factory.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
Makita Corporation Anjo, Aichi, Japan 885071A222 16 www.makita.
