Operation Manual

6
ENG221-1
Vibration
The vibration total value (tri-axial vector sum)
determined according to EN60745-2-13:
Work mode : cutting wood
Vibration emission (a
h
) : 4.2 m/s
2
Uncertainty (K) : 1.5 m/s
2
For Model BUC122
ENG101-2
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-13:
Sound pressure level (L
pA
) : 84.6 dB(A)
Uncertainty (K) : 2 dB(A)
The noise level under working may exceed 85 dB (A).
Wear ear protection.
ENG221-1
Vibration
The vibration total value (tri-axial vector sum)
determined according to EN60745-2-13:
Work mode : cutting wood
Vibration emission (a
h
) : 4.3 m/s
2
Uncertainty (K) : 1.5 m/s
2
ENH016-5
EC-DECLARATION OF CONFORMITY
The undersigned, Kato, as authorized by, declare that
the MAKITA machines,
EU model identification No.:M6 08 02 24243 083
BUC121
complies with the standard safety and health
requirements of the pertinent EU guidelines:
EU machinery guideline 98/37/EC, Noise emission
2000/14/EG, EU EMC guideline.
The requirements of the above EU guidelines were
implemented chiefly on the basis of the following
standards: EN60745-2-13, EN 55014, ENISO11681.
The conformity assessment procedure 2000/14/EG was
performed per Annex V. The measured sound power
level (Lwa) is 92.0 dB(A). The guaranteed sound power
level (Ld) is 94 dB(A). The EU Type-Examination per
98/37/EG was performed by: TÜV Product Service
GmbH, Zertifizierungsstelle, Ridlerstraße 31, D-80339
München.
Tomoyasu Kato CE2007
000230
Director
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
ENH016-5
EC-DECLARATION OF CONFORMITY
The undersigned, Kato, as authorized by, declare that
the MAKITA machines,
EU model identification No.:M6 08 02 24243 083
BUC122
complies with the standard safety and health
requirements of the pertinent EU guidelines:
EU machinery guideline 98/37/EC, Noise emission
2000/14/EG, EU EMC guideline.
The requirements of the above EU guidelines were
implemented chiefly on the basis of the following
standards: EN60745-2-13, EN 55014, ENISO11681.
The conformity assessment procedure 2000/14/EG was
performed per Annex V. The measured sound power
level (Lwa) is 92.7 dB(A). The guaranteed sound power
level (Ld) is 95 dB(A). The EU Type-Examination per
98/37/EG was performed by: TÜV Product Service
GmbH, Zertifizierungsstelle, Ridlerstraße 31, D-80339
München.
Tomoyasu Kato CE2007
000230
Director
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
GEB037-1
Chain saw safety warnings:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to chain saw safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
1. Keep all parts of the body away from the saw
chain when the chain saw is operating. Before
you start the chain saw, make sure the saw
chain is not contacting anything. A moment of
inattention while operating chain saws may cause
entanglement of your clothing or body with the
saw chain.
2. Always hold the chain saw with your right
hand on the rear handle and your left hand on
the front handle. Holding the chain saw with a
reversed hand configuration increases the risk of
personal injury and should never be done.
3. Wear safety glasses and hearing protection.
Further protective equipment for head, hands,
legs and feet is recommended. Adequate
protective clothing will reduce personal injury by
flying debris or accidental contact with the saw
chain.