INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Impact Driver Atornillador de Impacto Inalámbrico XDT15 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Fastening capacities No load speed (RPM) Impacts per minute XDT15 Machine screw 4 mm - 8 mm (5/32" - 5/16") Standard bolt 5 mm - 14 mm (3/16" - 9/16") High tensile bolt 5 mm - 12 mm (3/16" - 1/2") Hard impact mode 0 - 3,000 /min Soft impact mode 0 - 1,300 /min Hard impact mode 0 - 3,900 /min Soft impact mode 0 - 1,600 /min Rated voltage D.C.
5. 6. 7. Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2. Follow instruction for lubricating and changing accessories. 3. Keep handles dry, clean and free from oil and grease. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery.
. 5. 6. 7. 8. 9. 10. 11. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain.
Overheat protection Indicating the remaining battery capacity When the tool/battery is overheated, the tool stops automatically. In this situation, let the tool/battery cool before turning the tool on again. Only for battery cartridges with "B" at the end of the model number Overdischarge protection When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery.
Lighting up the front lamp Reversing switch action CAUTION: Do not look in the light or see the source of light directly. A B 1 1 ► 1 . Reversing switch lever CAUTION: Always check the direction of rotation before operation. ► 1 . Lamp CAUTION: Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. CAUTION: When not operating the tool, always set the reversing switch lever to the neutral position.
Changing the impact force 1 You can change the impact force in three steps: hard, soft, and A mode. This allows a tightening suitable to the work. Every time the button is pressed, the number of blows changes in three steps. 4 “A mode (assist mode)” is an easy-to-use mode for driving screws with good control. In this mode, the tool drives a screw with low-speed rotation at first. After the tool starts to impact, the rotation speed increases and reaches the maximum speed.
Installing or removing driver bit/ socket bit Installing hook Optional accessory 12 mm (15/32”) 1 9 mm (3/8”) 2 3 ► 1 . Groove 2. Hook 3. Screw The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out. Use only the driver bit/socket bit shown in the figure.
Standard bolt NOTE: Use the proper bit for the head of the screw/ bolt that you wish to use. N•m (ft•lbs) NOTE: When fastening M8 or smaller screw, choose a proper impact force and carefully adjust pressure on the switch trigger so that the screw is not damaged. 120 (87) 2 NOTE: Hold the tool pointed straight at the screw.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de apriete Velocidad sin carga (RPM) Impactos por minuto XDT15 Tornillo de máquina 4 mm - 8 mm (5/32" - 5/16") Tornillo estándar 5 mm - 14 mm (3/16" - 9/16") Tornillo de alta resistencia 5 mm - 12 mm (3/16" - 1/2") Modo de impacto duro 0 r/min - 3 000 r/min Modo de impacto suave 0 r/min - 1 300 r/min Modo de impacto duro 0 ipm - 3 900 ipm Modo de impacto suave 0 ipm - 1 600 ipm Tensión nominal 18 V c.c.
6. Si no es posible evitar usar una herramienta eléctrica en condiciones húmedas, utilice un alimentador protegido con interruptor de circuito de falla a tierra (ICFT). El uso de un ICFT reduce el riesgo de descarga eléctrica. 4. Seguridad personal 1. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice una herramienta eléctrica cuando esté cansado o bajo la influencia de drogas, alcohol o medicamentos.
2. 3. 4. 5. 6. piezas metálicas expuestas de la herramienta eléctrica se cargarán también de corriente y el operario puede recibir una descarga. Asegúrese siempre de que pisa sobre suelo firme. Asegúrese de que no haya nadie debajo cuando utilice la herramienta en lugares altos. Sujete la herramienta con firmeza. Póngase protectores de oídos. No toque la broca o pieza de trabajo inmediatamente después de la operación. Podrían estar extremadamente calientes y provocarle una quemadura.
Indicación de la capacidad restante de la batería DESCRIPCIÓN DEL FUNCIONAMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería haya sido extraído antes de realizar cualquier ajuste o comprobación en la herramienta. Sólo para cartuchos de batería con una “B” al final del número de modelo Instalación o extracción del cartucho de batería 1 PRECAUCIÓN: Apague siempre la herramienta antes de colocar o quitar el cartucho de batería.
Protección contra sobrecarga Cuando la batería se esté utilizando de una manera que cause que consuma una cantidad de corriente anormalmente alta, la herramienta se detendrá automáticamente sin indicación alguna. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla. Para poner en marcha la herramienta, simplemente apriete el gatillo interruptor.
NOTA: Para confirmar el estado de la lámpara, jale el gatillo. Cuando la lámpara se enciende al jalar el gatillo interruptor, el estado de la lámpara está activado. Cuando la lámpara no se enciende, el estado de la lámpara está desactivado. NOTA: Cuando la herramienta se sobrecalienta, la luz parpadea durante un minuto, y luego la pantalla LED se desactiva. En este caso, deje enfriar la herramienta antes de usarla de nuevo. NOTA: Utilice un paño seco para quitar la suciedad de la lente de la lámpara.
Grado de la fuerza de impacto mostrado en el panel Golpes máximos Propósito Ejemplo de aplicación Duro 3 900 ipm Apriete cuando se requiere fuerza y velocidad. Apriete de tornillos para madera, apriete de pernos. Suave 1 600 ipm Apriete con menos fuerza para evitar que se rompa la rosca del tornillo. Apriete de tornillos de banda, apriete de tornillos pequeños como el de 6 mm. Modo A 3 900 ipm Apriete de tornillos con un mejor control. Apriete de tornillos largos.
Perno estándar Instalación del gancho N•m (ft•lbs) 120 N•m (87 ft•lbs) 1 2 2 3 100 N•m (72 ft•lbs) 14 mm(9/16") 80 N•m (58 ft•lbs) 12 mm(1/2") 14 mm(9/16") 60 N•m (43 ft•lbs) 12 mm(1/2") 40 N•m (29 ft•lbs) ► 1 . Ranura 2. Gancho 3. Tornillo 8 mm(5/16") 20 N•m (14 ft•lbs) El gancho resulta útil para colgar temporalmente la herramienta. Se puede instalar en cualquiera de los lados de la herramienta.
NOTA: Utilice la broca apropiada para la cabeza del tornillo/perno que desee utilizar. NOTA: Cuando fije un tornillo de 8 mm o más pequeño, elija una fuerza de impacto apropiada y ajuste cuidadosamente la presión sobre el gatillo interruptor para evitar que el tornillo se dañe. NOTA: Sujete la herramienta dirigida en línea recta al tornillo.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Recipro Saw Sierra Recíproca Inalámbrica XRJ07 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XRJ07 Length of stroke 20 mm (13/16″) Strokes per minute Max. cutting capacities 0 - 3,000 /min Pipe 130 mm (5-1/8″) Wood (with 300 mm (11-3/4″) blade) 255 mm (10″) Rated voltage D.C. 18 V Standard battery cartridge BL1815N, BL1820B, BL1830, BL1830B, BL1840B, BL1850B, BL1860B Overall length 316 mm (12-1/2″) Net weight • • • 2.6 - 2.9 kg (5.7 - 6.
5. 6. 7. 8. 9. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Check for the proper clearance beyond the workpiece before cutting so that the blade will not strike the floor, workbench, etc. Hold the tool firmly. Make sure the blade is not contacting the workpiece before the switch is turned on. Keep hands away from moving parts. Do not leave the tool running. Operate the tool only when hand-held. Always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece.
Overload protection FUNCTIONAL DESCRIPTION When the battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.
NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. CAUTION: Do not look in the light or see the source of light directly. Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The lamp goes out approximately 10 seconds after releasing the switch trigger.
Insert the recipro saw blade into the blade clamp as far as it will go. The blade clamp sleeve rotates and fixes the recipro saw blade. Make sure that the recipro saw blade cannot be extracted even though you try to pull it out. NOTE: If you remove the recipro saw blade without rotating the blade clamp lever fully, the lever may not be locked in the released position . In this case, rotate the blade clamp lever fully again, then make sure that the blade clamp lever locked at the released position .
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XRJ07 Extensión de la carrera 20 mm (13/16″) Carreras por minuto Capacidad máxima de corte 0 cpm - 3 000 cpm Tubo 130 mm (5-1/8″) Madera (con la segueta de 300 mm (11-3/4″)) 255 mm (10″) Tensión nominal 18 V c.c.
6. 7. Si no es posible evitar usar una herramienta eléctrica en condiciones húmedas, utilice un alimentador protegido con interruptor de circuito de falla a tierra (ICFT). El uso de un ICFT reduce el riesgo de descarga eléctrica. Las herramientas eléctricas pueden producir campos electromagnéticos (CEM) que no son dañinos para el usuario.
Uso y cuidado de la herramienta a batería 1. Recargue sólo con el cargador especificado por el fabricante. Un cargador que es adecuado para un solo tipo de batería puede generar riesgo de incendio al ser utilizado con otra batería. 2. Utilice las herramientas eléctricas solamente con las baterías designadas específicamente para ellas. La utilización de cualquier otra batería puede crear un riesgo de lesiones o incendio. 3.
10. Símbolos A continuación se muestran los símbolos utilizados para la herramienta. volts o voltios corriente directa o continua velocidad sin carga revoluciones o alternaciones por minuto, frecuencia de rotación 11. Instrucciones importantes de seguridad para el cartucho de batería 1. 2. 3. 4. 5. 6. 7. 8. 9. 12.
Sistema de protección para la herramienta/batería DESCRIPCIÓN DEL FUNCIONAMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería haya sido extraído antes de realizar cualquier ajuste o comprobación en la herramienta. Instalación o extracción del cartucho de batería La herramienta está equipada con un sistema de protección de la herramienta/batería.
Luces indicadoras Iluminadas Apagadas Freno eléctrico Capacidad restante La herramienta está equipada con un freno eléctrico. Si la herramienta falla constantemente en detenerse tras soltar el gatillo interruptor, lleve la herramienta a mantenimiento a un centro de servicio Makita. Parpadeando 75% a 100% Iluminación de la luz delantera 50% a 75% 25% a 50% 1 0% a 25% Cargar la batería. La batería pudo haber funcionado mal.
1 2 3 2 1 ► 1 . Segueta recíproca 2. Palanca de la abrazadera de la segueta ► 1 . Palanca de la abrazadera de la segueta 2. Posición liberada 3. Posición fija Inserte la segueta recíproca en el manguito de sujeción de la segueta hasta su punto máximo. El manguito de abrazadera de la segueta gira fijando la segueta reciproca. Asegúrese de que la segueta recíproca no pueda ser extraída incluso cuando intente jalarla hacia afuera.
OPERACIÓN PRECAUCIÓN: Siempre presione firmemente la zapata contra la pieza de trabajo durante la operación. Si durante la operación la zapata es extraída o colocada lejos de la pieza de trabajo, se producirá una fuerte vibración y/o torcedura ocasionando que el disco se rompa de manera peligrosa. PRECAUCIÓN: Siempre use guantes para proteger las manos de las rebabas calientes que salgan despedidas al cortar metales.
Esta garantía le concede derechos legales específicos y usted podrá tener también otros derechos que varían de un estado a otro. Algunos estados no permiten la exclusión o limitación de daños incidentales o consecuentes, por lo que la limitación o exclusión arriba mencionada podría no aplicar para usted. Algunos estados no permiten la limitación sobre la duración de una garantía implícita, por lo que la limitación arriba mencionada podría no aplicar para usted.
18
19
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Driver Drill Atornillador Taladro Inalámbrico XFD11 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XFD11 Drilling capacities Steel Fastening capacities Wood screw 13 mm (1/2") Wood 36 mm (1-7/16") 6 mm x 75 mm (1/4" x 2-15/16") Machine screw No load speed (RPM) M6 (1/4") High (2) 0 - 1,700 /min Low (1) 0 - 500 /min Overall length 162 mm (6-3/8") Rated voltage D.C. 18 V Standard battery cartridge Net weight • • • BL1815N, BL1820B BL1830, BL1830B, BL1840B, BL1850B, BL1860B 1.3 kg (2.8 lbs) 1.5 kg (3.
6. 7. Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2. Follow instruction for lubricating and changing accessories. 3. Keep handles dry, clean and free from oil and grease. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
2. Important safety instructions for battery cartridge 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. Do not disassemble battery cartridge. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
Overdischarge protection Indicating the remaining battery capacity When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery. Only for battery cartridges with "B" at the end of the model number NOTE: Overheat protection (for battery) will work only with batteries with star marking. 1 1 2 ► 1. Indicator lamps 2. Check button ► 1.
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. Lighting up the front lamp Speed change 1 ► 1. Lamp CAUTION: Do not look in the light or see the source of light directly. 1 Pull the switch trigger to light up the lamp.
Adjusting the fastening torque 1 2 3 ► 1. Adjusting ring 2. Graduation 3. Arrow The fastening torque can be adjusted in 21 levels by turning the adjusting ring. Align the graduations with the arrow on the tool body. You can get the minimum fastening torque at 1 and maximum torque at marking. The clutch will slip at various torque levels when set at the number 1 to 20. The clutch does not work at the marking.
Installing driver bit holder Screwdriving operation Optional accessory CAUTION: Adjust the adjusting ring to the proper torque level for your work. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or driver bit may be damaged. 1 Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the switch trigger as soon as the clutch cuts in.
• • • • • Using the tool as a hand screwdriver Drill bits Driver bits Driver bit holder Hook Makita genuine battery and charger NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XFD11 Capacidades de taladrado Acero Capacidades de apriete Tornillo para madera 13 mm (1/2") Madera 36 mm (1-7/16") 6 mm x 75 mm (1/4" x 2-15/16") Tornillo de máquina Velocidad sin carga (rpm) 6 mm (1/4") Alta (2) 0 - 1 700 r/min Baja (1) 0 - 500 r/min Longitud total 162 mm (6-3/8") Tensión nominal 18 V c.c.
2. 3. 4. 5. 6. 7. cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera las herramientas eléctricas puede terminar en una lesión grave. Use equipo de protección personal. Póngase siempre protección para los ojos. El equipo protector tal como máscara contra el polvo, zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. Impida el encendido accidental.
3. 4. 5. 6. 7. 8. 9. Sujete la herramienta eléctrica por las superficies de agarre aisladas al realizar una operación en la que el sujetador pueda entrar en contacto con cables ocultos. Si el sujetador entra en contacto con un cable con corriente, las piezas metálicas expuestas de la herramienta eléctrica se cargarán también de corriente y el operario puede recibir una descarga. Asegúrese siempre de que pisa sobre suelo firme.
2. 3. 4. No cargue nunca un cartucho de batería que esté completamente cargado. La sobrecarga acortará la vida de servicio de la batería. Cargue el cartucho de batería a una temperatura ambiente de 10 °C - 40 °C (50 °F - 104 °F). Si un cartucho de batería está caliente, déjelo enfriar antes de cargarlo. Cargue el cartucho de batería si no va a utilizarlo durante un período prolongado (más de seis meses).
Protección contra sobrecarga Cuando la herramienta/batería se esté utilizando de una manera que cause que consuma una cantidad de corriente inusualmente alta, la herramienta se detendrá automáticamente sin que haya indicación alguna. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla.
Accionamiento del conmutador de inversión de giro A Cambio de velocidad B 1 1 ► 1. Palanca de cambio de velocidad ► 1. Palanca del interruptor de inversión PRECAUCIÓN: Coloque siempre la palanca de cambio de velocidad exactamente en la posición correcta. Si usted utiliza la herramienta con la palanca de cambio de velocidad puesta a medias entre la posición “1” y “2”, la herramienta puede dañarse. PRECAUCIÓN: Confirme siempre la direc- ción de rotación antes de la operación.
La torsión de apriete puede ajustarse en 21 niveles girando el anillo de ajuste. Alinee las graduaciones con la flecha en el cuerpo de la herramienta. Puede conseguir una fijación de torsión mínima en 1 y una torsión máxima en la . marca El embrague se deslizará entre los diferentes niveles de torsión cuando esté ajustado en los números 1 a 20. El embrague no funciona en la marca .
Coloque el portabrocas en la protuberancia en la base de la herramienta o ya sea del lado derecho o izquierdo y asegúrelo con un tornillo. Cuando no utilice la punta de destornillador, manténgala dentro del portabrocas. Las puntas de destornillador de 45 mm de largo (1-3/4") se pueden guardar ahí. Operación de taladrado Primero, gire el anillo de ajuste de tal forma que la flecha apunte hacia la marca . Después proceda como sigue.
Si necesita cualquier ayuda para más detalles en relación con estos accesorios, pregunte a su centro de servicio local Makita. • Brocas de taladro • Puntas de destornillador • Portabrocas • Gancho • Batería y cargador originales de Makita Uso de la herramienta como atornillador manual NOTA: Algunos de los artículos en la lista pueden incluirse en el paquete de la herramienta como accesorios estándar. Éstos pueden variar de país a país. GARANTÍA LIMITADA DE UN AÑO DE MAKITA Apague la herramienta.
19
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.