ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Brad Nailer DBN500 014580 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model DBN500 Brad nail size 18 Ga x 15, 20, 25, 30, 32, 35, 38, 40, 45, 50 mm Brad nail magazine capacity 100 pcs Dimensions (L x W x H) 294 mm x 97 mm x 318 mm Rated voltage D.C. 18 V Net weight 3.3 kg 3.5 kg Standard battery cartridges BL1815 / BL1815N / BL1820 / BL1820B BL1830 / BL1840 / BL1840B / BL1850 / BL1850B • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
ENH003-15 tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 5. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Service 28. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 29. Follow instruction for lubricating and changing accessories. 30.
11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. ENC007-9 Make sure no one is nearby before operation. Never attempt to drive fasteners from both the inside and outside of wall at the same time. Fasteners may rip through and/or fly off, presenting a grave danger. Watch your footing and maintain your balance with the tool. Make sure there is no one below when working in high locations.
FUNCTIONAL DESCRIPTION • 1. Battery indicator 1 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 014584 1. Red indicator 2. Button 3. Battery cartridge 2 1 Overheat protection for tool When the tool is overheated, the tool stops automatically and the indicator blinks about 60 seconds. In this situation, let the tool cool before turning the tool on again.
Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for few seconds. Nailing mode selection 1 2 Indicator lamps Remaining capacity Lighted Off Blinking 1. Mode selecting button 2. Sequential mode 3. Continuous mode 75% to 100% 3 50% to 75% 014618 The tool has two different nailing modes. Select the desired nailing by the mode selecting button. For more detail, see the section "OPERATION".
To turn on the lamp, pull the trigger or place the contact element against the workpiece. Release the trigger or contact element to turn it off. The lamp goes out 10 seconds after releasing the trigger or contact element from the workpiece. 1. Nails 2. Slide door 3. Driver guide 3 NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.
Driving nails CAUTION: Always be sure to first place the contact element against the workpiece before pulling the trigger. Select the nailing mode by pressing the mode selecting button as mentioned in the section "Nailing mode selection". Intermittent nailing (sequential mode) • 014587 2 1. Groove 2. Hook 3. Screw 3 2 1 1 1. Place the contact element against workpiece. 2. Pull the trigger 014619 To drive a nail, set the lock button to the "FREE" position.
Anti dry fire mechanism This tool is equipped with an anti dry fire mechanism. It automatically stops driving nails when the remaining nails finish. In this case, load more nails to resume operation. Humid Removing jammed nails • Nail WARNING: Always make sure that the trigger is released, and the battery cartridge and nails are removed before removing jammed nails. 3 2 004311 Avoid storing nails in a very humid or hot place or place exposed to direct sunlight. MAINTENANCE 1. Hex bolt A 2.
2. 3. Install the parts onto the pusher in the correct order, sleeve, small spring and then stopper. Install the pusher with the other parts onto the slide door. NOTE: • When you pull out the pusher from the slide door, the parts in the slide door may bounce out. • When you install the pusher with the other parts to the slide door, make slight spaces between the pusher and sleeves.
Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan 885334A226 www.makita.
