ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Finish Nailer DBN600 Read before use.
SPECIFICATIONS Model: DBN600 Nail size 16Ga x 25 / 30 / 32 / 35 / 38 / 40 / 45 / 50 / 57 / 60 / 64 mm Magazine capacity 100 pcs. Dimensions without hook (L x W x H) (when using BL1840B battery) 296 x 108 x 318 mm Rated voltage D.C. 18 V Net weight • • • 3.4 - 3.8 kg Due to our continuing program of research and development, the specifications herein are subject to change without notice. Specifications may differ from country to country.
devices should contact the maker of their device and/ or doctor for advice before operating this power tool. EC Declaration of Conformity For European countries only The EC declaration of conformity is included as Annex A to this instruction manual. SAFETY WARNINGS General power tool safety warnings WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
Power tool use and care 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3.
13. 14. 15. 16. 17. 18. 19. 20. 21. 22. when working in high locations. Never use fastener driving tools marked with the symbol "Do not use on scaffoldings, ladders" for specific application for example: • when changing one driving location to another involves the use of scaffoldings, stairs, ladders, or ladder alike constructions, e.g. roof laths; • closing boxes or crates; • fitting transportation safety systems e.g. on vehicles and wagons.
Overload protection FUNCTIONAL DESCRIPTION When the tool/battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.
Indicator lamps Lighted Intermittent nailing (sequential mode) This mode suits for driving a nail carefully and accurately. Remaining capacity Off Continuous/ intermittent nailing (continuous mode) When the tool is set to this mode, you can choose either continuous or intermittent nailing by sequences of the trigger operation. Blinking The battery may have malfunctioned.
1 1 ► 1. Pusher lever ► 1. Lamp 3. Insert a connected nails into the slit on the bottom of the magazine. NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. NOTE: The nailer may not fire nails even if the lamp lights up because the remaining battery power is low. In this case, charge the battery cartridge.
Nose adapter CAUTION: Always make sure that your fingers are not placed on the switch trigger or the contact element and the battery cartridge is removed before installing the nose adapter. When firing nails on the material with easily-marred surfaces, use the nose adapter. Put the nose adapter on the front end of the contact element. Make sure that the nose adapter completely covers the front end of the contact element as illustrated. The hook is convenient for temporarily hanging the tool.
CAUTION: Do not drive nails on hard materials such as metal or the like. If the nail cannot penetrate the material, the nailer may be kicked back toward you and cause injury. NOTE: If you drive nails continuously for a long time, the exhaust air will get hot due to the heat from the motor. The tool employs two nailing actions: intermittent nailing (sequential mode) and continuous/intermittent nailing (continuous mode).
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan www.makita.
